Ultimaker 3D printers

6,534 topics in this forum

1. Using the correct side of an Ultimaker glass plate

   By SandervG, January 25
   • 24 replies
   • 3,079 views
   • 
   • mayo77
   • October 5

2. Cura not working - No space left on device

   By SmartBlug, 7 hours ago
   • 5 replies
   • 30 views
   • 
   • Smithy
   • 49 minutes ago

3. Stratasys F170..F370

   By TheRealJoost, Tuesday at 10:48 PM
   • 24 replies
   • 206 views
   • 
   • TheRealJoost
   • 8 hours ago

4. Ultimaker 3 Won't Boot

   By superslimeboy, November 6, 2016
   • 17 replies
   • 3,170 views
   • 
   • cmceezee
   • Friday at 07:44 PM

5. Ultimaker 3 Extended power problem

   By sproutdesign, November 2, 2016
   • 6 replies
   • 1,684 views
   • 
   • cmceezee
   • Friday at 07:16 PM

6. Max temp CC core

   By Job_van_gennip, Thursday at 11:44 AM
   • 1 reply
   • 42 views
   • 
   • Job_van_gennip
   • Friday at 02:18 PM

7. How to set IP address without WiFi or DHCP 1 2

   By Nooger, November 3, 2016   

   • UM3
   • 46 replies
   • 11,725 views
   • 
   • thorsenrune
   • Friday at 01:30 PM

8. Missing Screw UMS5

   By geetee, Wednesday at 10:15 PM
   • 3 replies
   • 62 views
   • 
   • stu_le_brew
   • Thursday at 11:15 PM

9. Temp Sensor problem - some clarification needed

   By cigoler, Thursday at 02:48 PM
   • 1 reply
   • 32 views
   • 
   • cigoler
   • Thursday at 04:44 PM

10. UM3 error: Printcore in print head slot 1 nozzle size mismatch

    By Niles, May 11
    • 13 replies
    • 1,098 views
    • 
    • CarloK
    • Thursday at 04:41 PM

11. Ultimaker S5 disconnects from Cura Connect frequently

    By thelemurking, September 26   

    • CURA
    • UMS5
    • 9 replies
    • 419 views
    • 
    • g.davis
    • Thursday at 10:05 AM

12. Ultimaker 2, bed temp error issue

    By Viggoman, Wednesday at 03:41 PM
    • 0 replies
    • 18 views
    • 
    • Viggoman
    • Wednesday at 03:41 PM

13. Dash lines on the top layer

    By pineirod, February 6
    • 15 replies
    • 596 views
    • 
    • Smithy
    • Tuesday at 08:19 PM

14. New UM 2+ help

    By 1nf1n1ty, October 5
    • 20 replies
    • 294 views
    • 
    • Smithy
    • Tuesday at 05:19 PM

15. X-offset with PVA

    By master-mugen, Tuesday at 01:57 PM
    • 3 replies
    • 39 views
    • 
    • Job_van_gennip
    • Tuesday at 03:21 PM

16. UM2+ skipping steps

    By njic, December 7   

    • HELP
    • UM2+
    • (and 1 more)

      Tagged with:

      • HELP
      • UM2+
      • PLA
    • 6 replies
    • 127 views
    • 
    • stu_le_brew
    • Monday at 06:32 PM

17. Lubricate the feeder gear

    By NBull, Monday at 01:46 PM
    • 1 reply
    • 44 views
    • 
    • Smithy
    • Monday at 02:13 PM

18. Ultimaker 5S Bundle delayed again. Now til February?

    By SubmarinePilot, December 6
    • 4 replies
    • 155 views
    • 
    • Elfonerio
    • Monday at 02:06 PM

19. Ultimaker 3 something is not right with this axle

    By hbo67, December 8
    • 4 replies
    • 55 views
    • 
    • Smithy
    • December 8

20. Auto bed level error Video.

    By dubbsd, November 27
    • 2 replies
    • 93 views
    • 
    • dubbsd
    • December 7

21. auto bed level Error

    By dubbsd, November 23   

    • HELP
    • 2 replies
    • 77 views
    • 
    • dubbsd
    • December 7

22. Ultimaker S5 - Constantly says it's out of filament, when it's not... 1 2

    By nano-l, November 5, 2018   

    • HELP
    • UMS5
    • 29 replies
    • 2,824 views
    • 
    • Carla_Birch
    • December 6

23. S5 Calibration cube with odd corners

    By jantograaf, December 5
    • 4 replies
    • 99 views
    • 
    • Smithy
    • December 5

24. UM3 - Home head issue

    By gilbert666, October 14
    • 3 replies
    • 110 views
    • 
    • Smithy
    • December 5

25. S5 flow rate & printing blobs in infill

    By jantograaf, December 5   

    • UMS5
    • 4 replies
    • 63 views
    • 
    • Smithy
    • December 5