Jump to content
Ultimaker Community of 3D Printing Experts

pretengineer

Dormant
  • Posts

    4
  • Joined

  • Last visited

    Never

pretengineer's Achievements

0

Reputation

  1. I haven't had the chance to try it with the upgrade, I'll post results at the weekend when I give it a try.
  2. Pronterface connects almost instantly. I have to swap out my heatbed thermistor for one that Marlin won't read as absolute zero so until then, I'm stuck with Sprinter. I've only realised there's a new version of Cura available so I'll upgrade and see if that helps.
  3. Error Log Changing monitoring state from 'Offline' to 'Opening serial port' Connecting to: COM8 Connected to: Serial<id=0x350c670, open=True>(port='COM8', baudrate=115200, bytesize=8, parity='N', stopbits=1, timeout=0.1, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor Changing monitoring state from 'Opening serial port' to 'Detecting baudrate' Trying baudrate: 250000 Send: M105 Baudrate test retry: 4 Send: M105 Baudrate test retry: 3 Send: M105 Baudrate test retry: 2 Send: M105 Baudrate test retry: 1 Send: M105 Baudrate test retry: 0 Send: M105 Trying baudrate: 230400 Send: M105 Baudrate test retry: 4 Send: M105 Baudrate test retry: 3 Send: M105 Baudrate test retry: 2 Send: M105 Baudrate test retry: 1 Send: M105 Baudrate test retry: 0 Send: M105 Trying baudrate: 115200 Send: M105 Baudrate test retry: 4 Send: M105 Baudrate test retry: 3 Send: M105 Baudrate test retry: 2 Send: M105 Baudrate test retry: 1 Send: M105 Baudrate test retry: 0 Send: M105 Trying baudrate: 57600 Send: M105 Baudrate test retry: 4 Send: M105 Baudrate test retry: 3 Send: M105 Baudrate test retry: 2 Send: M105 Baudrate test retry: 1 Send: M105 Baudrate test retry: 0 Send: M105 Trying baudrate: 38400 Send: M105 Baudrate test retry: 4 Send: M105 Baudrate test retry: 3 Send: M105 Baudrate test retry: 2 Send: M105 Baudrate test retry: 1 Send: M105 Baudrate test retry: 0 Send: M105 Trying baudrate: 19200 Send: M105 Baudrate test retry: 4 Send: M105 Baudrate test retry: 3 Send: M105 Baudrate test retry: 2 Send: M105 Baudrate test retry: 1 Send: M105 Baudrate test retry: 0 Send: M105 Trying baudrate: 9600 Send: M105 Changing monitoring state from 'Detecting baudrate' to 'Closed' Changing monitoring state from 'Closed' to 'Error: No more baudrates to...' Connection closed, closing down monitor I should mention that I had this same problem with a RAMPS 1.3 board and a different Arduino as well.
  4. Hi, I've recently downloaded Cura 12.12 to use with my RepRap Prusa but I can't get it to connect. When I click connect in the print dialog, it goes from 'Machine State: Detecting baudrate' to 'Machine State: Error: No more baudrates...' I've tried setting different baudrates in the firmware but no luck. I've been using Slic3r and Pronterface for the past few weeks with little to no issues. I'm using RAMPS1.4 and Sprinter software. Any ideas on a solution?
×
×
  • Create New...