pretengineer
-
Posts
4 -
Joined
-
Last visited
Never
Content Type
Forums
Events
3D Prints
Posts posted by pretengineer
-
-
Pronterface connects almost instantly. I have to swap out my heatbed thermistor for one that Marlin won't read as absolute zero so until then, I'm stuck with Sprinter. I've only realised there's a new version of Cura available so I'll upgrade and see if that helps.
-
Error Log
Changing monitoring state from 'Offline' to 'Opening serial port'
Connecting to: COM8
Connected to: Serial<id=0x350c670, open=True>(port='COM8', baudrate=115200, bytesize=8, parity='N', stopbits=1, timeout=0.1, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
Changing monitoring state from 'Opening serial port' to 'Detecting baudrate'
Trying baudrate: 250000
Send: M105
Baudrate test retry: 4
Send: M105
Baudrate test retry: 3
Send: M105
Baudrate test retry: 2
Send: M105
Baudrate test retry: 1
Send: M105
Baudrate test retry: 0
Send: M105
Trying baudrate: 230400
Send: M105
Baudrate test retry: 4
Send: M105
Baudrate test retry: 3
Send: M105
Baudrate test retry: 2
Send: M105
Baudrate test retry: 1
Send: M105
Baudrate test retry: 0
Send: M105
Trying baudrate: 115200
Send: M105
Baudrate test retry: 4
Send: M105
Baudrate test retry: 3
Send: M105
Baudrate test retry: 2
Send: M105
Baudrate test retry: 1
Send: M105
Baudrate test retry: 0
Send: M105
Trying baudrate: 57600
Send: M105
Baudrate test retry: 4
Send: M105
Baudrate test retry: 3
Send: M105
Baudrate test retry: 2
Send: M105
Baudrate test retry: 1
Send: M105
Baudrate test retry: 0
Send: M105
Trying baudrate: 38400
Send: M105
Baudrate test retry: 4
Send: M105
Baudrate test retry: 3
Send: M105
Baudrate test retry: 2
Send: M105
Baudrate test retry: 1
Send: M105
Baudrate test retry: 0
Send: M105
Trying baudrate: 19200
Send: M105
Baudrate test retry: 4
Send: M105
Baudrate test retry: 3
Send: M105
Baudrate test retry: 2
Send: M105
Baudrate test retry: 1
Send: M105
Baudrate test retry: 0
Send: M105
Trying baudrate: 9600
Send: M105
Changing monitoring state from 'Detecting baudrate' to 'Closed'
Changing monitoring state from 'Closed' to 'Error: No more baudrates to...'
Connection closed, closing down monitor
I should mention that I had this same problem with a RAMPS 1.3 board and a different Arduino as well.
-
Hi,
I've recently downloaded Cura 12.12 to use with my RepRap Prusa but I can't get it to connect. When I click connect in the print dialog, it goes from 'Machine State: Detecting baudrate' to 'Machine State: Error: No more baudrates...'
I've tried setting different baudrates in the firmware but no luck. I've been using Slic3r and Pronterface for the past few weeks with little to no issues.
I'm using RAMPS1.4 and Sprinter software.
Any ideas on a solution?
Cura 12.12 with RAMPS 1.4 connection issue
in UltiMaker Cura
Posted
I haven't had the chance to try it with the upgrade, I'll post results at the weekend when I give it a try.