Jump to content

Bearwood

Member
 View Profile  See their activity

  • Posts

    5

  • Joined

  • Last visited

 Content Type 

Posts posted by Bearwood

    Mirrored prints duet wifi

    in Third party products & modifications

    Posted

    I'm embarrassed to write this but i'm getting mirrored prints (Y axis) on my Ultimaker 2 clone using a Duet 2 wifi running firmware 3.11. It prints well just mirrored?

    All axis move in the correct direction and I can home each axis independently as well as home all axis.

     

    I have all manor of configurations, in fact so many that I have lost track. For the life of me I can not get the Y axis to print the correct way. I can make Cura mirror the print but that is not the correct way to fix this and besides I am likely to forget to do that sometime in the future. 

     

    The X and Y axis end-stops are in the top rear left corner. The Z end-stop is at the top.

     

    My config: 

    ; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Sep 19 2020 18:43:32 GMT+1200 (NZST)

; General preferences
G90                                     ; send absolute coordinates...
M83                                     ; ...but relative extruder moves
M550 P"Ultimaker 2"                     ; set printer name

; Network
M551 P"JTMalibu"                        ; set password
M552 S1                                 ; enable network
M586 P0 S1                              ; enable HTTP
M586 P1 S0                              ; disable FTP
M586 P2 S0                              ; disable Telnet

; Drives
M569 P0 S0                              ; physical drive 0 goes reverse
M569 P1 S0                              ; physical drive 1 goes forwards
M569 P2 S0                              ; physical drive 2 goes reverse
M569 P3 S0                              ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                        ; set drive mapping
M350 X16 Y16 Z16 E16 I1                 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E580.00       ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00     ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z2400.00 E2700.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z500.00 E250.00     ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E1150 I30            ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                        ; set axis minima
M208 X225 Y220 Z216 S0                  ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                     ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                     ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop"		 		  	 ; configure Z endstop


; Z-Probe
;M558 P1 C"zprobe.in" H5 F120 T6000      ; set Z probe type to unmodulated and the dive height + speeds
;G31 P500 X0 Y0 Z2.5                     ; set Z probe trigger value, offset and trigger height
;M557 X15:215 Y15:195 S20                ; define mesh grid

; Heaters
M308 S0 P"spi.cs1" Y"rtd-max31865"      ; configure sensor 0 as thermocouple via CS pin spi.cs1
M950 H0 C"bedheat" T0                   ; create bed heater output on bedheat and map it to sensor 0
M307 H0 A90.3 C219.5 D0.9 V23.9 B0      ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                 ; map heated bed to heater 0
M143 H0 S120                            ; set temperature limit for heater 0 to 120C
M308 S1 P"spi.cs2" Y"rtd-max31865"      ; configure sensor 1 as thermocouple via CS pin spi.cs2
M950 H1 C"e0heat" T1                    ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B1 S1.00                        ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                    ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1                          ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                    ; create fan 1 on pin fan1 and set its frequency
M106 P1 S0.75 H1 T75                       ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                        ; define tool 0
G10 P0 X0 Y0 Z0                         ; set tool 0 axis offsets
G10 P0 R0 S0                            ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                       ; enable support for PanelDue
M501                                    ; load saved parameters from non-volatile memory

     

    homey .g: 

    ; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Sep 19 2020 17:43:53 GMT+1200 (NZST)
G91               ; relative positioning
G1 H2 Z5 F6000   ; lower Z relative to current position
G1 H1 Y-215 F3600 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000    ; go back a few mm
G1 H1 Y-215 F360  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; raise Z again
G90               ; absolute positioning

     

×
×
  • Create New...