dcp360
-
Posts
11 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by dcp360
-
-
I have an ultimaker original plus.
Recently, every print the layer shits suddenly in the x-y direction about mid-way through the print. It then continues to print normally but in the completely wrong place.
I have checked the pulleys, the belts, the end stops and have downloaded the latest Cura.
I read that the stepper motors might be getting too hot - but posibbly not the case as they should be able to manage 80 degrees or it could be the pcb part overheating.
Could it possibly be the g-code or the sd card?
Thank you.
-
Thank you for the replies.
neotko- I simply do not have the time to do the procedure 8+ times and testing it. I need the printer to work to prototype designs for university (final year).
gr5 - I have done all of these things without success. It must be either the quality of the parts or I am missing something really really obvious.
The printer is still in warranty - so I am asking Ultimaker (3DGBIRE) for replacement parts for the main assembles which I think are causing the problems.
Thank you for your help!
-
That makes sense, I will try this when I have the time.
Is there anything else which I could try?
-
-
I have followed those steps, I'll test it out now.
-
I stored them
P = 27.94
I = 2.46
D = 79.19
Max was about 155? is that max temperature? abit low?
-
I followed what you did...
[01mT:149>[00m M301 P0.00 I0.00 D0.00
SENDING:M301 P0.00 I0.00 D0.00
ok p:0.00 i:0.00 d:0.00 c:1.00
[01mT:108>[00m M303 S150
SENDING:M303 S150
PID Autotune start
bias: 43 d: 43 min: 148.91 max: 155.78
bias: 41 d: 41 min: 148.44 max: 151.72
bias: 40 d: 40 min: 148.83 max: 151.09
Ku: 44.96 Tu: 22.68
Classic PID m
Kp: 26.98 m
Ki: 2.38 m
Kd: 76.46 m
bias: 40 d: 40 min: 148.98 max: 151.48
Ku: 40.74 Tu: 22.81
Classic PID m
Kp: 24.45 m
Ki: 2.14 m
Kd: 69.69 m
bias: 38 d: 38 min: 149.06 max: 151.33
Ku: 42.71 Tu: 21.76
Classic PID m
Kp: 25.63 m
Ki: 2.36 m
Kd: 69.70 m
PID Autotune finished! Put the last Kp, Ki and Kd constants from above into Configuration.h
How do I store them?
-
Checked the diameter and it seems to be okay throughout the roll.
90degrees, nothing happens.
100degrees - nothing happens
approx 110degrees it bubbles.
-
Originally I had some pronounced ridging on the surface of the prints. So I thought it might be something to do with the Z - Axis. I have greased and moved it up and down to check for any bad signs and I can't see any. Also, tightening the screws.
I have tried a range of different temperatures and settings in Cura and tried the atomic method. Im presuming the filament is good quality, so it will not have an inconsistent diameter.
-
Hello all,
I am having problems with the surface finish on my prints. Finished prints either have gaps or large ridges at regular intervals.
The printer is Ultimaker Original Plus.
I have done some research on other threads and forums and tried everything, still having problems.
Any help would be amazing! I have attatched an image of some example prints.
Thank you.
Layer shifts mid-way through the print.
in UltiMaker 3D printers
Posted
Different parts and it occurs at different heights.