ixenriquez
-
Posts
6 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by ixenriquez
-
-
Again, to be clear, not installing any E3D hot ends, only the E3D Titan extruders. I have two UM2 hotends from Aliexpress and installed those to be compatible with the Mark2 upgrade. I have also included pictures of my setup for clarity. Everything works for a single nozzle setup in UltimakerMarlin, but not Mark2. Could it be as simple as installing a different temp sensor? If so, which is recommended. Here is what I got from Ponterface @tinkergnome. Thank you for your support.
Connecting...
start
Printer is now online.
echo:Marlin 1.0.0
echo: Last Updated: Oct 7 2017 18:25:39 | Author: Tinker_Mark2_17.09
Compiled: Oct 7 2017
echo: Free Memory: 2274 PlannerBufferBytes: 1232
echo:Hardcoded Default Settings Loaded
echo:Steps per unit:
echo: M92 X80.00 Y80.00 Z200.00 E369.00
echo:Maximum feedrates (mm/s):
echo: M203 X300.00 Y300.00 Z40.00 E45.00
echo:Maximum Acceleration (mm/s2):
echo: M201 X9000 Y9000 Z100 E10000
echo:Acceleration: S=acceleration, T=retract acceleration
echo: M204 S3000.00 T3000.00
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)
echo: M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00
echo:Home offset (mm):
echo: M206 X0.00 Y0.00 Z0.00
echo:PID settings:
echo: M301 P12.00 I0.75 D55.00
echo:Dual setup: enabled
echo:Home offset z2 (mm): 0.00
echo:Dock position: X223.00 Y43.00
echo:Firmware wipe: disabled
echo:Wipe position: X105.00 Y27.00
Error:1
[ERROR] Error:1: Extruder switched off. MAXTEMP triggered !
Error:Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
[ERROR] Error:Printer stopped due to errors. Fix the error and use M999 to restart.
-
I cant do anything after install the Mark2 Firmware. It immediately goes to the error and doesn't allow anything else.
-
I have not changed the hot ends, just the extruders. All I have done is change the extruders and extended the z build volume to around 360mm. I input modified values into Ultimaker2Marlin with arduino and the machine works very well when I do. When I try and install any Mark 2 firmware after my initial modification I keep getting the mentioned error. I just want the expanded capabilities of the dual head. Everything is printed, assembled, and connected for the Mark 2 upgrade, including the official expansion board. Its just this error that keeps holding me back.
-
No, I was able to print perfectly fine before. I did not compile firmware for the Mark 2. I just mentioned that I modified the Ultimaker2Marlin firmware as the instructions given online to replace the extruders for E3D Titian extruders. I also increased the Z_Max_Pos to accommodate mu custom case. So everything works perfectly fine when I manually modify it in arduino for Ultimaker2Marlin. When I try and install any version on the available Mark 2 firmware hex files, I get the previously mentioned error. The earlier 17.02 gives me Error - Stopped Temp sensor free Go to: Ultimaker.com/ER01 and 17.06 & 17.09 give me Error - Stopped Temp sensor 2228 bytes free Go to: Ultimaker.com/ER01. I have tested it against four different temp sensors. Seems to be some sort of software issue from what I figure.
-
Hello everyone, looking for some help. I have been trying to upgrade my custom Ultimaker 2 to a Mark 2. Everything is assembled and installed, including the expansion board. Though mo matter what version of Cura and Mark 2 Firmware I use, all that I keep getting is "Error - Stopped Temp sensor 2228 bytes free Go to: Ultimaker.com/ER01" I have used Cura 15.04.21 & 3.2.1 with every single firmware the Mark 2 offers and I'm still stuck. .I know its not the sensor or the board. Both are responsive and work flawlessly when I run the machine with regular firmware.
Additionally, not sure how to change the following values in the Mark 2 firmware, when I finally get it running. I only know how to change the values in Arduino and then upload them to the machine through USB. The important part is that I changed my Ultimaker case and added two E3D Titan Extruders. My current working values are as follows. I basically want the Mark 2 mod with these additional values.
Z_Max_Pos 400
DEFAULT_AXIS_STEPS_PER_UNIT (80.0, 80.0, 200, 837)
DEFAULT_MAX_FEEDRATE (300, 300, 40, 20)
DEFAULT_MAX_ACCELERATION (9000, 9000, 100, 3000)FILAMENT_REVERSAL_LENGTH (FILAMENT_BOWDEN_LENGTH = 150)
FILAMENT_REVERSAL_SPEED 75
FILAMENT_INSERT_FAST_SPEED 75
Any help is very much appreciated. Just want to print with two materials already, Thanks everyone.
Ultimaker Mark2 - The Smart Dual-Extrusion Upgrade
in Third party products & modifications
Posted
Thank you @tinkergnome. Ill try and do some tests, hopefully its just the sensor.