dupton
-
Posts
16 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by dupton
-
-
Hi,
'Im nor sure I'm in the right htread but I'll ask anyway.
can anyone let me know where I can source Birchwood 2.8mm, PLA?
I had ordered it from a local supplier here in Ireland but he can't source it.
Also if anyone has used it can they give me a heads up on the settings/ things to be aware of, or is it just the same as standard PLA?
Thanks in advance
-
My polybox readings are , temp 21.5 , humidity 28%. Hopefully these values are stable and adequate for 3d printing.
-
at last my polybox has arrived!!!
I want to mount it behind the ultimaker on an extended shelf ( on my old portable computer trolly) to get it as close as possible to the infeeders so I'm wondering can I remove the ultimaker spool holder ? I have another container for my spare spools and plan to put it on the bottom shelf, currently occupied by the polybox. My ultimate goal is to have a dedicated portable 3d printing station that can be rolled out to trouble shoot the feeder mechanisms should they need attention.
-
Cheers ! I just ordered 2 spares from https://www.makerpoint.nl/en/print-table-glass-s5.html.
Thanks again, Dermot
-
Hi , I have just finished a batch of parts on my S5 and need to get the printer going again with another batch but I have to take the finished parts
from the glass bed first. This takes 15 to 20 mins turn around. So I'm wondering if it would be an advantage to have a second glass bed waitting to
place into my S5 and start the printer and then clean off my finished prints from the first print?? Any advice would be helpful .
Thanks in advance, Dermot
-
Sure enough Smithy the filament was damaged which resulted in no feed. Thanks again for the advice.
Dermot
-
I have changed the material to Generic and the printer has accepted the file so fingers crossed!!!!
-
-
Hi. I keep getting a error message when I send this to print on the network. my material selection is set corrrectly (as per image) the slice function looks fine but when I send it to print this mesage appears but if I overide the message the print goes missing and I have to abort. Has anybody encountered this before?
Thanks in Advance , Dermot
-
That's good to know because I'm in the process of buying a polybox and some storage vessels. there must be a sensor in the spool arm that detects the utimaker pva?
-
That polybox is just what I need so . I will also have a look for some sealable containers and get some silica gel while I'm at it.
I'm using PLA (white, black , silver) and natural PVA filaments for the time being until I get familiar with the 3D printing process. Thanks again you've saved me a lot of hardship on the learning curve!
-
I changed to a new reel of PVA and the first thing I noticed was how ridgid and almost brittle the filament of the new reel is compared to the old reel that I took off. The old reel filament was very compliable to the touch so hopefully that will solve the issue for me. I am new to this so I'm trying to build a preventative maintenance mini programe to deal with the histories and issues. The old reel had been sitting on the back of the printer for a few weeks in a spare bedroom. I did not know how sensitive the PVA filament is. I will build a container to keep it stable but for the time being I have the old reel in the sealed bag that came with the new reel. fingers crossed!!!!
Thanks again Smithy.
-
Thanks fbrc8-erin, how does my filament get ground down? It looks o.k. Its PVA Filament thats causiing me the issues and it looks fine on the reel. I cleaned the tubes this morning and might get some new tubing as spares before I change out a reel of material. I measured the tubing and its 1/4 O.D. 1/8 I.D. clear tubing so I might give that a try before I get into to it futher.
-
cheers Smithy, I must try turning off the sensor to get it finished but I have to find a long term solution. my prints take 1 to 2 days on average and I don't want to babysit the machine.
-
Hello, my ultimaker s5 keeps stopping and displaying this error. I have read the blogs and have tried to fix it but to no avail. I have disabled the network . that didn't help.
I have the latest firmware loaded. that didn't fix it either. I took the feeder apart and cleaned it . that didn't fix it. I have a print job on and its a 2.5 day print. I have 1 day and 5 hours left and am sick of restarting the printer. is there any PERMANENT solution to this error?
highly frustrated, Dermot
Birchwood PLA 2.8mm
in Materials & profiles
Posted
Hi,
'Im nor sure I'm in the right htread but I'll ask anyway.
can anyone let me know where I can source Birchwood 2.8mm, PLA?
I had ordered it from a local supplier here in Ireland but he can't source it.
Also if anyone has used it can they give me a heads up on the settings/ potential issues to be aware of, or is it just the same as standard PLA?
Thanks in advance
Dermot