-
Posts
26 -
Joined
-
Last visited
-
Days Won
1
Content Type
Forums
Events
3D Prints
Posts posted by jangermann
-
-
-
Awesome quality. But you will not use that as a real engine part or?
I saw on youtube a video a guy builded brushless motor case and he tried to run it. After hundred of rpm it was cracking really dangerous. At 3:14
oh s...!! he should wear a full face helmet when testing things like that.
Well the house seems very thin, so I guess he could expect that result.
No I will not use it in an engine :-) just as key hanger.
-
-
To all who is having problems with melted fan mounts. Maybe you should try to use alu tape. It reflects the heat.
-
did you just wrap the block in alufoil ?
Yes :-)
Took a sheet of alufoil, half A4, folded multible times, cut a hole, and then wrap around the heater.
-
-
I can now confirm that V14.12 is fine.
-
Thanks for your answers.
I will try V14.12 to night and post the result.
-
This is my first vase attempt with Cura, and I am not happy :sad:
When printing, the extruder stops for a very short time, every round of the vase, this leaves a small dot.
It leaves a spiralize path of dots on the print.
Is this a Cura 14.09 bug??
Trying to print this model (it is solid and should be OK)
http://www.thingiverse.com/download:114887
Se the problem here:
Why oh why?
-
You print to fast.
slow down to 20mm/s and add 25% fan speed.
-
Ok. Thanks again for all your answers.
-
Printet ok on my 2 week old UM2.
-
Thansk for your answers.
Ok, so the Z-scars on my model is normal?
Do yours also do this?
Please note that this is "only" a problem when printing above 0.1mm layers. Below that, the scars is very small and barely noticeable.
-
I can see while printing, when the UM2 makes the dot.
http://germann.dk/webbilleder/dotpoint.jpg
Maybe the dots cant be avoided??
Are all here experience dots as in the links above?
-
Or Tinkercad.com
I use it all the time and it is just SO very easy!
-
For 3D scanning just use this program: http://skanect.occipital.com/%C2%A0
And a cheap xbox 360 kinect sensor (I did buy mine uset for almost nothing).
I have scanned my kid, and printed here out. Is it amazing! 3D scanning is for everyone!
-
PM_dude thanks for your answer. When I print the model there are no retraction.
The dots come every time a layer is finish, where it join the inner perimeter with the outer perimeter.
I have now tried adjusting temp,flow,speed, and still the same result. Very visible dots when printing 0.2mm layers :sad:
This is simply NOT what I was expecting from my brand new ultimaker2 :???:
Pictures after filament change.
http://germann.dk/webbilleder/dots1.jpg
http://germann.dk/webbilleder/dots2.jpg
-
I have now tried to change filament to a non ultimaker filament and also changed the diameter to 2.90 (measured on the filament), and played with the temperatures, it don't change anything.... same problem with dots.
BUT when I now print in 0.2mm after filament change, I see the dots again, but as small holes. Before when printing with the ultimaker PLA the dots were popping out, as too much material.
I think it's time to play with the flow rate.
-
I have now printed the same model in 0.15mm layers, it is much better, but I still see the dots. They are smaller now but still visible.
In 0.1, and if I look really close, I also see the dots. Even in 0.08mm I see micro dots.
It seems like the problem always is there, but with smaller layers you get smaller dots.
Yes I am using Cura V14.09
-
Hi
I´m new to UM2 but not 3D printing.
I have been printing in 0.08mm and 0.1mm layers without any problems.
Last night I was printing in 0.2mm and got some nasty dots and some stripes.
The printing conditions:
-Ultimaker PLA
-Filament 2.85mm
-Speed 25mm/s
-Hotend 200deg
-No infill
-Wall 0.8mm
http://germann.dk/webbilleder/um1.jpg
http://germann.dk/webbilleder/um2.jpg
Any ideas?
hope you have :-)
-
Ok, thanks for your answers and ideas. I can defiantly use the cylinder idea.
BUT I for sure miss that parameter!
-
Hi.
When I print the ultimaker robot, and it is printing the antennas, it print two layers on each antenna before it proceed. I want it to print one layer and then proceed to the next antenna, where i prints one layer and the back again to the first antenna.
Two layers in a row on the small antennas will cause melting and I would like to avoid that :smile:
Is there a parameter for adjusting this?
Thanks.
Jan.
-
Ok, Thanks gr5. I think I will use the SD card in the future, or at least until Ultimaker comes with another solution.
I have tried the Doodle3D, but I don't want to disable ultigcode, print quality is my priority.
Thanks again.
-
Hi.
I'm all new to Ultimaker2, but have been using Cura a couple of month on my Velleman K8200.
Now I am the happy owner of the UM2, and it's really great.
My problem is that I can't print directly from Cura (is it even possible with the UM2, can't find ANY information about it??)
I can firmware update the UM2 - Yes no problem (so the communication must be ok).
I can copy code to the SD card an print from SD
But how....please tell me how do I print directly from Cura?? I load a model and expect that I would see the print button, but its not there???
What are I doing wrong?
Ultimaker Forum | Feedback
in UltiMaker.com
Posted
Automatic follow?? What is that. I now get 2-4 mails from this forum every day.