johnfrank
-
Posts
12 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by johnfrank
-
-
-
UPDATE
Tried to print with same speed for oulines, inner, infills, etc. I dont know if this was a solution but my prints are better. Still i have lines and artifacts. ( i printed with acceleration at 3000)
-
Hello Sander and thank you for your response. Yes i printed feet to give more height and also i added cooling fans to cool the mainboard. Now i gave a print with 3000 acceleration at XY. I will update soon.
PS i think that the layer shifting got worst because i tighten the belts without changing the acceleration. Now i print with tightened belts, again calibrated axis and new acceleration
-
Update
Still same results with Cura. Maybe if i lower down the acceleration from 9000 to 5000 will see some results
-
Update
It seems that ove extrusion is not a problem. Looks like layer shifting i suppose.
All the walls meant to be flat. I will print now with cura this time. Although i dont think it is software problem
-
Hello! Thank you all for your replies and response! Im using Simplify 3D. What i did further is to re calibrate the axis, lubricant again, added cooling fans with external power to the mainboard and passive coolers too. Also i tightened the belts with these ones https://www.youmagine.com/designs/belt-tensioner
I see a lot better prints but i think that you are right SandervG.. It must be a over extrusion problem.
-
UPDATE
Calibrated again the axis and printed at 0.1 layer height. The problem remain the same. The next thing i will try is to add a cooling fan on the electronics board. I touched one stepper transistor and its veeeeery hot. Maybe is this the problem?
-
Hello, i have problems with Ultimaker Original Plus lately and i cant achieve a good print. I have level the bed million times, calibated axis another million, oiled the rods but with no results. I ll post some photos printed at 0.15mm, and im hoping your experienced eyes see the problem. Thanks Giannis
-
My country is Greece. Yes of course is a good printer. But when you dont have time to "play" with the printer and you want a work just to be done perfectly i think that ultimaker isnt that good. Although ultimaker 2 are very good and quality printers.. But i dont risk to give 6000 euros for 2 ulti printers.. I will go with Witbox or Wasp Delta
-
First of all i have to admit that Ultimakers are wonderfull machines. But when i have a company i prefer a good machine with superb support than the Best machine with no support. So my problem is that no more than 3 months ago i bought the ultimaker original + so i can learn how printers work and have a machine for my prototypes. After 1 month the fan stop working. I checked all the possible causes and i ended up that the transistor is faulty. Its been from 21 May that i mailed the support to replace my mainboard but from then no news. Second mail and still no news. I tried to buy the mainboard but they dont sell the v2 only v1.5.7 with a price of 190€!!!! So i made an external source of fans with dimmer and power supply. 5 days now i am enjoying my new Zortrax M200. Excellent machine with excellent support and reseller in my country! I liked Ultimaker and i was planning to buy 2 Ultimakers2 extended for my company. But i cant trust them anymore. BQ witbox i think will be my next buy
-
Hello, today my printhead fan stopped working and after tests with a polymeter i found that there is a problem in the pcb board. I have an UMO+. The question is that i bought a ramps 1.4 with arduino 2560 because i am waiting for my support ticket and i cant stand so many days without printing. The problem is that i cant find UMO+ firmware to upload on arduino and some i found in here dont communicate with the printer. Also Cura doesnt recognise the printer. Any thoughts?
Thanks, John
Parts of the print pulled out or in
in UltiMaker 3D printers
Posted
Thank you for your response! I did PID tune to heat bed but with no result :( i cant find the solution.. Do i have to buy an anti backlash nut?
How much acceleration and speed can the z motor handle?