[I'm selling my UM 2 how much would I get for it]

I decided to put it up for auction at a starting price 1100€

http://www.ebay.de/itm/-/252328887638?

[I'm selling my UM 2 how much would I get for it]

It currently has around 500 printing hours however besides the the broken heating cartridge everything else works well

[I'm selling my UM 2 how much would I get for it]

I am going to sell my UM2 since I have upgraded to the Ultimaker extended plus

how much would I get for it on eBay or a similar website.

however the printer is not in perfect shape last week the heater cartridge has broken I also don't have much experience repairing something like this. so I have decided to rather sell the entire unit since it became kind of unnecessary to have two ultimakers anyway .also the printer has a small dent in one of its feet however it never effected any prints.

[My UM2 displays the following error message Z screw stuck]

I have fixed the problem by replacing the switch with a new one

[My UM2 displays the following error message Z screw stuck]

I have checked the switch which and it seems to be completely broken

[My UM2 displays the following error message Z screw stuck]

My UM2  displays the following error message Z screw stuck

However the bill played moves freely by hand but the Um2 is not able to lower the built played even when requested through the advanced menu when I pressed the lower button it just brings the bill plate further up

[extruding problems with ultimaker v2 using olsson block]

Yes it does look like the first layer is quite squished

Should I do another bed calibration

[extruding problems with ultimaker v2 using olsson block]

It's the stock filament what comes with the Ultimaker. it happens in the first layer as well as the layers after. But it doesn't happen in every print even if it is the same model sometimes it does sometimes it doesn't under extrude so it's not really consistent

[extruding problems with ultimaker v2 using olsson block]

I'm currently using the 0.4 nozzle and getting extruding problems add 210c 50mms

The printer is four days old should be undamaged as well as clean and teflon should still be as good as new I currently have a 2 mm gap in between the stainless steel isolator and the teflon like recommended in the Ultimaker ios app.

I always change the nozzle at around 150c since it is a lot easier at that temperature

I have did some cold pulls like you recommended but it make no difference :(

[extruding problems with ultimaker v2 using olsson block]

I seem to have an extruding problems with ultimaker v2 using olsson block by using th 0.4 and 0.8 nozzle

I can hear the stepper motor skipping steps and see an under extrudin in my prints what should I do

210C nozzle

60C bad

50mm/s speed

I have seen this problem occur in 100 to 200 microns z resolution

[Olsson block What is the distance supposed to be from the ptfe coupler and the heater block isolator??]

What is the distance supposed to be from the ptfe coupler and the heater block isolator??

[What to do with my damaged ultimaker]

I have checked the frame it seems like it wobbles on a flat surface by around 2.5mm. Will this be a problem? However all the electronics still seem to work.

[What to do with my damaged ultimaker]

First picture:

Is the belt very tight on the top and very loose on the bottom? If so, undo the set screws on the pulleys that the belt is running over and "jiggle" the belt a bit and that should even out the tension.

Second picture:

This isn't necessarily a big deal. If the rod is held in place reasonably well I think the printer will still perform very well.

Third:

This is a bit of a bigger problem. If it were me I would try to remove the bed (undo the three thumbscrews underneath and it comes right off) and then try to bend as close to flat as possible and try it out. If no traces have cracked I'm sure it'll work fine as long as you don't have any massive gaps between the glass plate and the heated bed.

If nothing else, two new sliding blocks, possibly a new belt and a new heated bed PCB should be available from your local dealer (or they can get it for you from Ultimaker). With those parts replaced I think it should be fine.

But it would probably be a good idea to really inspect everything on the printer, like checking the frame and so on, since it looks like it took quite a hit.

 

Thanks for your reply! I have checked the frame it seems like it wobbles on a flat surface by around 2.5mm. Will this be a problem? However all the electronics still seem to work.

[What to do with my damaged ultimaker]

What should I do with my damage ultimaker it got damaged during shipping to another locationnm.

I have already replaced the unit. However is it worth or possible to repair the unit are should I sell it on eBay how much would I still get for it.

[/media]

The belts have also lost the tension between them.