Improve your 3D prints

5,412 topics in this forum

1. Tip: Bed adhesion 1 2 3 4

   By SandervG, February 20, 2018
   • 87 replies
   • 39.4k views
   • 
   • jirodriguez72
   • September 21, 2022

2. Why do I get Bulging Corners?

   By Phatwarren, 13 hours ago
   • 3 replies
   • 49 views
   • 
   • gr5
   • 2 hours ago

3. Print one at a time until certain layer then start next object

   By rachmellwood, July 11
   • 5 replies
   • 159 views
   • 
   • rachmellwood
   • Yesterday at 07:17 AM

4. Mesh hollow when infill is set to 100% along side one layer being completely filled in when needed to be hollow!

   By HungryToast, July 15
   • 1 reply
   • 225 views
   • 
   • GregValiant
   • July 16

5. Newby problems (Ender 3 S1)

   By Fresh3D, July 14
   • 4 replies
   • 117 views
   • 
   • Slashee_the_Cow
   • July 15

6. Printing PETG Issues, Layers Above supports Not Inline

   By laziraven, April 27, 2023
   • 14 replies
   • 1.3k views
   • 
   • PartySausage
   • July 13

7. Outer surface

   By cpaidas, July 12
   • 10 replies
   • 178 views
   • 
   • GregValiant
   • July 13

8. Holes/gaps where they seam is

   By Xhoax, July 8   

   • Ultimaker S3
   • cura5.6
   • 18 replies
   • 375 views
   • 
   • Torgeir
   • July 11

9. Autoscaling by 10,000% of original size

   By rickyz, February 24, 2021   

   • Help
   • 4 replies
   • 6.4k views
   • 
   • djjoma
   • July 11

10. Under/over-extrusion or other problem?

    By nonnos, July 3
    • 5 replies
    • 170 views
    • 
    • gr5
    • July 5

11. UM3 Under-extrusion at Random Layers

    By cmd348, July 3
    • 2 replies
    • 146 views
    • 
    • cmd348
    • July 4

12. problems with the bed

    By xilit922, July 1
    • 3 replies
    • 123 views
    • 
    • Slashee_the_Cow
    • July 3

13. Ultimaker S3 - TPU 95A print

    By Cerejo, June 27
    • 5 replies
    • 201 views
    • 
    • Cerejo
    • July 1

14. Option "Custom Support" in Cura 5.7.2

    By German, June 28
    • 1 reply
    • 158 views
    • 
    • Slashee_the_Cow
    • June 29

15. Ultimaker S3 - underextrusion?

    By Xhoax, June 25
    • 13 replies
    • 324 views
    • 
    • gr5
    • June 28

16. Under extrusion but only on columns

    By Hasslefish, June 22
    • 5 replies
    • 177 views
    • 
    • Hasslefish
    • June 28

17. My ender 5 stopped printing

    By champsteve778, June 24
    • 5 replies
    • 165 views
    • 
    • GregValiant
    • June 26

18. Elegoo mars 1 build plate

    By jasonlegal35, June 25
    • 2 replies
    • 103 views
    • 
    • Dustin
    • June 25

19. Some PVA problems..

    By rscudder, June 24   

    • PVA
    • Stringing
    • 4 replies
    • 139 views
    • 
    • rscudder
    • June 24

20. Slice at an angle 1 2

    By msundman, February 1, 2021   

    • Help
    • 40 replies
    • 6.9k views
    • 
    • GregValiant
    • June 22

21. Can't get rid of CHEPCube lines

    By MrLonnie, June 21
    • 7 replies
    • 151 views
    • 
    • MrLonnie
    • June 22

22. Infill issue

    By mhmdhn, June 15
    • 1 reply
    • 159 views
    • 
    • Slashee_the_Cow
    • June 15

23. Slicing changes depending on models the models on the build plate.

    By MrLonnie, June 11
    • 7 replies
    • 205 views
    • 
    • Slashee_the_Cow
    • June 13

24. Print optimization

    By Goldbergoson, June 7
    • 5 replies
    • 223 views
    • 
    • jaysenodell
    • June 10

25. build plate adhesive

    By kingfisher-tam, May 27
    • 8 replies
    • 373 views
    • 
    • jaysenodell
    • June 7