Lobopt
-
Posts
10 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by Lobopt
-
-
Really strange....
Nozzle size and fan % ?
Standard 0.4 and gradually increasing fan speed 0 at stArt 30 at 5 layers 60 at 80 layers and 100 at 120 layers worked well for 2 months . Btw at 0.2 layers are half of 0.1 . Always verifying the temp curve so it only moves up and down about 3 degrees c in any way
Ok found out it was simply too slow for that part the head dragged it around.
C etait trop lent la tete a tire la piece dans tous les sens.
-
1
-
-
I think that it can be installed on a um2go (if you mean the feeder of um2+). But mind that it will hit the spool and it won't fit on the transport box. I think they didn't release it for um2go just for that. But technically it should work,
mind that you will need to mod it with printed parts (that you might need to design) to make it work.
[/quote
Well i have a stand spool holder so that wouldnt be a real problem and i bought the go because i couldnt afford the bigger ones yet and not to run around so that wouldnt be my problem:)
The only issue I can think then it's that the cables are 20cm longer, so you will have to grip them somewhere so they don't disturb you, there's plenty of room bellow the printer.
Oh there's other problem that maybe someone with more knowhow can answer. The um2+ uses a 35W heater, um2go I think uses 25W. Worse case scenario you might need to swap the one you have to the um2+ hotend. I know that um2go uses a less powerfull powersupply, but I don't know the actual numbers.
Hi heater is the same as um2 difference why they put a lighter psu is no heated bed .mechanically all pieces except rods are exactly the same as an um2 ,even the board is the same with all connections only heated bed is off in firmware.
-
Really strange....
Nozzle size and fan % ?
Standard 0.4 and gradually increasing fan speed 0 at stArt 30 at 5 layers 60 at 80 layers and 100 at 120 layers worked well for 2 months . Btw at 0.2 layers are half of 0.1 . Always verifying the temp curve so it only moves up and down about 3 degrees c in any way
-
You tried with a lower temperature ? 190 - 200
Oh yes much much worse then but only at low speed what baffles me a bit.
-
I would be quite interested in a 2 go version.
That would be really nice.
Well i would also like a heated bed on it why it hasnt one while it has everything ready ,connectors on board and such , for it surprises me a little for the price.
I think that it can be installed on a um2go (if you mean the feeder of um2+). But mind that it will hit the spool and it won't fit on the transport box. I think they didn't release it for um2go just for that. But technically it should work,
mind that you will need to mod it with printed parts (that you might need to design) to make it work.
Well i have a stand spool holder so that wouldnt be a real problem and i bought the go because i couldnt afford the bigger ones yet and not to run around so that wouldnt be my problem:)
[/quote
-
Filament ? PET or PETG ?
Pla with 215 c
-
Hi have a strange problem , i have heavy underextrusion on my 2 go when i print at 0.1 with 30 mm/s but perfect prints resolution wise at 0.2 with 60 mm/s at same temperature.
I dont really understand since normally it should be the other way.
-
Well the 2go power supply is significantly cheaper (and less power) than the other UM2 printers so you need to do special stuff to get it to work. But 3dsolex has a heated bed kit for the um2go for roughly 99€ (didn't check price).
not sure what you mean by "2go version". Are you referring to the "plus" upgrade?
Yeah meant the + upggrade for the go would be nice have also a spoolholder from another printer i can set away so that wouldnt be a problem
-
I would be quite interested in a 2 go version.
That would be really nice.
Well i would also like a heated bed on it why it hasnt one while it has everything ready ,connectors on board and such , for it surprises me a little for the price.
Simplify 3 d and new firmware trouble
in UltiMaker Cura
Posted
Since i upgraded the firmware on my 2 go all my prints at 0.1 are bad quality with simplify , cura works fine , but i bought simplify because of the support adding and removing function .
Btw 0.2 has no problem.