christiank21
-
Posts
9 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by christiank21
-
-
You have underextrusion. What material is this? PLA? Usually PLA doesn't peel off like that but that's common with ABS and easily fixed.
Still - what material is this and what temperature (temperature is set on the printer, not in cura).
I think the default temp is 210C and assuming PLA and with .3mm layer times .4mm nozzle times 50mm/sec that equals 6mm^3/sec. That's a bit fast for 210C and PLA. Try raising the temp to 220C and making your layer height thinner - try .15mm also slow it down a bit to 35mm/sec. That should fix much of the quality problems.
I used a PLA not ABS. I try your settings.Thank you
-
Hi,
after many 3d printing with Ultimaker 2, I tried to print this small object .See the picture below.I used Cura version 15.04.6.I attached this pictures (in the pictures you see circled in orange).
Below are settings in Cura version 15.04.6:
Basic
Quality
Layer height (mm): 0.3
Shell thickness (mm): 0.8
Enable retraction: selected
Fill
Bottom/ Top thickness (mm): 0.6
Fill Density (%): 20
Speed and Temperature
Print speed (mm/s): 50
Support
Support type: None
Platform adhesion type: None
Machine
Nozzle size (mm): 0.4
Advanced
Quality
Initial layer thickness (mm): 0.3
Initial layer line width (%): 100
Cut off object bottom (mm): 0.0
Dual extrusion overlap (mm): 0.15
Speed
Travel speed (mm/s): 150.0
Bottom layer speed (mm/s): 20
Infill speed(mm/s): 0.0
Top/bottom speed(mm/s): 0.0
Outer shell speed(mm/s): 0.0
Inner shell speed(mm/s): 0.0
Cool
Minimal layer time (sec): 5
Enable cooling fan: selected
What can I do? How can I improve? Thank you very much.
Bye,
Christian.
-
The first extruder was original and after I installed the Olsson block at the same time. I don't disassembled any other parts also a extruder and sensor PT100 because it broke. In this time to printed normally and the feeder motor normally turned.The next day gave me problems.The nozzle heat up as usual.Watch the movie: http://we.tl/QGDZjWfSCB.
-
I do like as the video. I try turning it off and on again?
-
I recently updated Ultimaker 2, an extruder with Olsson block with different nozzles, but the feeder that I have installed this alternative UM2 Feeder - version two of IRobertI does not charge a PLA filament.The motor filament motor is idling.What can I do? I have to change with new feeder? Thank you very much.
-
Look at my tutorial, everything is explained and with pics.
The problem comes from the screw that is holding the bearing. It should not need a bolt and should be placed the other way around like this:
Hi,
thank you very much, alternative um2 feeder version-two about |Robert| works.
Thank you again.
Christian
-
-
Hello,
I installed the new feeder this from https://www.youmagine.com/designs/alternative-um2-feeder-version-two about |Robert|, but the screw in the left with the spring.It’s well? I entered the filament but is slow.
The left wheel touches the wheel to the right of motors.When I insert the filament does not pass between the two wheels, but slips out in the middle, see rectangle in colored in red.What should I do? See the picture: http://it.tinypic.com/r/2mebejp/8.
What can I do? Could you advise me how should I do? Someone can help me, please.Thank you very much.
Which Cura version for Mac OSX v.10.11.6
in UltiMaker Cura
Posted
What software Cura can I use for Mac OSX El Capitan v.10.11.6?