Produktdesigner
-
Posts
130 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by Produktdesigner
-
-
ok mache ich nochmal morgen
danke für deinen beistand.
-
Der Lüfter läuft.
Ja es sieht so aus, als wenn der Materialfluss irgendwann stockt.
Wenn ich das Filament herausziehe, hat sich nach den unteren 4 cm eine leichte Verdickung gebildet.
Ich habe mal einen neuen Druckkopf bestellt, mal schauen ob das was bringt.
-
Danke für deine Antwort, aber warum geht das dann in den ersten Minuten?
-
On 9/7/2018 at 7:10 PM, magura said:
An der Luftfeuchte liegts bei uns leider nicht. Auch mit neuen Rollen das gleiche Ergebnis.
Wir bekommen nächste Woche eine Haube für den Drucker. Vielleicht wirds mit konstanter Temperatur besser.
das bringt auch nix.
ändere doch mal die schicktdicke auf 0,15 oder 0,2 mm
-
Hallo,
ich habe das Phänomen, das mein Drucker mit einer 0,4 Düse nach einigen Minuten Druckzeit das Material stark ausdünnt. Danach wird durch die raue Modelloberfläche der ganze Druck von der Plattform gerissen. Liegt das wohl an der Düse?
Ich habe schon verschiedene Filamente ausprobiert. Das Ergebnis ist immer gleich.
-
Doch man kann die Messingdüse abschrauben. Man bekommt sie aber nicht mehr richtig drauf. Ich denke das ist eine Sollbruchstelle.
-
Hallo Nico,
ich habe jetzt versucht die Messingdüse abzuschrauben. Dabei ist der Druckkopft unterhalb der Kühlrippen gebrochen.
: (
-
Hallo,
nach einem Druckercrash blieb der Druckkopf von meinem UM3 einige Stunden im Material stehen. Jetzt ist er verstopft und es geht auch kein Material durch. Außerdem ist das Pla Filament über dem silbernem Röhrchen abgebrochen. Wie bekomme ich den Druckknopf wieder zum laufen?
-
Hello, I want to print a large part with my Ultimaker 3 ex. But it is not possible to use the ful size of 215x215 mm. What ist wrong?
I only need one filament without dual extrusion.
Any idea?
-
What is combing?
-
But I have only the 0,4 nozzle.
-
Hello,
I want to print a pipe with 1 mm wall thickness and a 65 mm diameter in PLA or ABS.
In my fist try I saw that the surface of the pipe has many small interruptions. How could I fix this. The surface has to be smooth.
Is it possible to print the part with 1 mm wall thickness in spiral mode? In the normal mode the nozzle is turning around many times.
-
Thank you all, that helps
-
Hello,
I have lost my calibration card for the leveling. How thick is this card?
- 1
-
Hello,
I have some bigger parts to built. The infil is about 20 %.
After a while the parts are breaking from the built base because the print head scraps over the infil of shape.
How could I change the settings that the problem is solved.
-
Thank you for this advice. I will try this out.
I didn't remebered this menu before.
-
Hello,
I want to print a 260 mm long part with the size of 7x20 mm on the ground. How could I do this in ABS?
I tried to build it landscape, but it blend from the base and I tried to print it vertical. Than after ca. 150 mm it move on the base and you see some defective areas on the part.
Any ideas how I could fix this?
-
Thank you,
with the new temperature settings I get better results.
The filament is from esun.
- 1
-
What are you using to adhere the material to the plate with? Is it lifting off completely The complete part is lifting. I use the standard settings for ABS. 60° C base temperature und 230° C for the nozzle.
-
Today I have tried to print with ABS. But this material doesn't stick on the base. Prittstift also doesn't help.
Any idea?
-
Danke für eure Antworten, es ist das Material von Ultimaker selber.
Es lässt sich einfach nicht drucken.
-
Hat jemand zufällig ein gutes Druckprofil für UM Nylon für Ultimaker3 in Verbindung mit PVA?
Ich möchte ein kleine filigranes Teil drucken und mit den Einstellungen von Ultimaker wird das Ergebnis nicht gut.
-
So what could i do?
-
what is cold pull?
I print nylon and pla. the problem start with nylon.
Was ist das beste Pla Filament für den Ultimaker 3?
in Deutsch
Posted
Was ist das beste Pla Filament für den Ultimaker 3?
wie sind eure Erfahrungen?