Jump to content

CostumeBiz

Member
  • Content Count

    22
  • Joined

  • Last visited

Community Reputation

0 Neutral

Personal Information

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. So I should paste this script into S3D? AFAIK G28 ; home all axes G1 X20 Y10 F3000 ; bring extruder to front G92 E0 ; zero the extruded length G1 Z10 ; lower G1 E19 F200 ; purge nozzle quickly G1 E26 F60 ; purge nozzle slowly G92 E0 ; zero the extruded length again G1 E-5.5 F400 ; retract G1 X190 Z0 F9000 ; pull away filament G1 X210 F9000 ; wipe G1 Y20 F9000 ; wipe G1 E0 ; feed filament back
  2. So far the print I am running on Cura is printing fine as before. I will pull the housing off in a couple days and check that screw, when I change out the print head with an Olson block.
  3. M907 E1400 ; increase extruder current G28 ; home all axes G1 X20 Y10 F3000 ; bring extruder to front G92 E0 ; zero the extruded length G1 Z10 ; lower G1 E19 F200 ; purge nozzle quickly G1 E26 F60 ; purge nozzle slowly G92 E0 ; zero the extruded length again G1 E-5.5 F400 ; retract G1 X190 Z0 F9000 ; pull away filament G1 X210 F9000 ; wipe G1 Y20 F9000 ; wipe G1 E0 ; feed filament back Here's the starting script from Simplify3D
  4. Could you also please tell me more about Tinker Marlin?
  5. Hmmmmm that just does not make sense why would the print go perfectly using Cura.. and wonky half thru using Simplify3D? Are you thinking the lack of speed control on S3D is causing slippage? Well I tightened all the screws I could reach... the one on the actual Y motor proved to hard to get the tool into. Bryn
  6. Thank you I will check the short belts on the stepper motor and test mark the belts. Simplify3D said to reduce the printing speed to 50% but at what layer height should I change the speed? In regards to the stepper motor I do have the unit enclosed as I am working with ABS but its not all that hot in there. Tinker Marlin? How can I install it and where can I get it. I have changed the jerk and acceleration settings on my CR10 for better prints can I do the same with Tinker Marlin?
  7. OK now the culprit has been made clear. It appears that there was no loose pulley afterall and that the problem was the slicing software First image with layer shifting was sliced by Simpllify3D image 2nd image by Cura. So why??? Why is Simplify3D sketchin out well past the midway of the print? I checked the print volume and the numbers where correct. I am at a loss... Hate using Cura but will be forced to if Simplify3D issues cannot be overcome.
  8. Ok on to the other portion of the sword. Started out great!! then as the print grew taller we can see variations in the layers starting to appear. I assume this is due to the shape and height of the item but what can be done to minimize loss of resolution???
  9. Bought some washers and put them on the rod where the spacer was missing.
  10. Yes found out I am missing a spacer??? on one of the y Axis rods.
  11. There was a very small build up on one arm just knocked it down with sand paper but seeing as I do not have to include additional objects in the print to get this quality I am good... the infill was 100%.
  12. Well I decided to check the tightness of the X Y pulleys and discovered that I am missing one of the 5mm spacers allowing one of the Y rods to move when the machine is covering a large area. Gonna go to the hardware store to see if I can find something to put there. As far as printing points goes...small projectiles and tubular items less than 1/4" diameter just do not print correctly. I am going to change over to a Olson block in a few days what fan mods has anyone played with? Can anyone show me pictures of successful pointy prints they have done on their UM's? and how they achieved them? Decided to print the part on my CR10 S5 she can handle these types of prints see image from the CR10 of the same model with the same supports.
  13. Oh masters of the Ultimaker universe I am printing a cross gaurd on my UM2E and it printed perfectly until the last 11 minutes then it slipped somehow and the filament isn't cooling fast enough and I am getting gobbly goop. I am using simplify3D and have changed the fan setting to 100% for layers less than 3 seconds. What else can be done?
×
×
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!