Sandi
-
Posts
11 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by Sandi
-
-
Update. Error ER999 occurs at every new layer. After finished layer head travels to starting position and from there back and begins printing new layer. At this time ER999 occurs.
-
I'd really like to get some response from Ultimaker. Please.
-
I'm getting ER999 all the time. Started suddenly. Tried tips from https://ultimaker.com/en/resources/52985-an-unspecified-error-has-occurred-er999 with no effect. Also noticed filament extraction during non printing movement.
Can I define what is causing error?
-
root@ultimakersystem-ccbdd3008xxx:~# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:1372 errors:0 dropped:0 overruns:0 frame:0
TX packets:1372 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:557981 (544.9 KiB) TX bytes:557981 (544.9 KiB)tether Link encap:Ethernet HWaddr 00:0E:8E:8A:1C:A1
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::bc4c:ff:fe92:d90f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:989 errors:0 dropped:0 overruns:0 frame:0
TX packets:523 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:87614 (85.5 KiB) TX bytes:78325 (76.4 KiB)wlan0 Link encap:Ethernet HWaddr 00:0E:8E:8A:1C:A1
inet6 addr: fe80::20e:8eff:fe8a:1ca1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:988 errors:0 dropped:0 overruns:0 frame:0
TX packets:904 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:101440 (99.0 KiB) TX bytes:141143 (137.8 KiB)root@ultimakersystem-ccbdd3008xxx:~# connmanctl
Error getting VPN connections: The name net.connman.vpn was not provided by any connmanctl>
connmanctl> exit
root@ultimakersystem-ccbdd3008xxx:~# connmanctl servicesroot@ultimakersystem-ccbdd3008xxx:~# ls
root@ultimakersystem-ccbdd3008xxx:~#
ls command also not working. Should I see eth0?
-
__ ______ _ __
/ / / / / /_(_)___ ___ ____ _/ /_____ _____
/ / / / / __/ / __ '__ \/ __ '/ //_/ _ \/ ___/
/ /_/ / / /_/ / / / / / / /_/ / ,< / __/ /
\____/_/\__/_/_/ /_/ /_/\__,_/_/|_|\___/_/
Welcome to our kingdom. Please be responsible.
(Cmd)
I'd like to repeat above procedure, but I get different prompt and commands are not working. I use username and password "ultimaker". Printer is S5. Where is a mistake?
-
I've lost two days cleaning, calibrating and printing with different setups. After downgrading to 4.1 works as it should.
-
Similar problem. Extruder starts printing after 10th layer.
-
Axes are not perpendicular. Y axe has about 6 mm or about 3 tooth difference relative to the left or right side.
This error was delivered to us. What mechanical accuracy Ultimaker guarantee?
-
Thank you for now. All suggestions I'll check on by one on Monday in the office. I will report the findings.
-
Hi!
I have new Ultimaker S5. I've double checked all setups, but can't find error. Diagonal difference is about 2%. W
hat could be the cause?
S5 ER999
in UltiMaker 3D printers
Posted
Let's close this topic. I changed the firmware and Cura version while error 999 was persistent. The local reseller spent several hours and did not find the cause. After that, I removed all Cura versions and stored profiles. After new Cura installation, there was a warning about corrupt profiles. ER999 disappeared.