[Supporti errati]

Ciao da quello che ho capito è semplicemente un opzione da disabilitare. In pratica il software ti propone in automatico il supporto anche con offset rispetto al pezzo, è necessario impostare di non fare questo offset, se non ricordo male mettendo 0 (zero) in quel parametro.

[how can I use the remaining filament from material station?]

Thanks @ Enigma_M4, I already try to splice the filament, but it is a long operation.
If I print for me in my hours I can this things, but when I print in the office I shouldn't take too hours for splice many pieces of filament, I tried but after 2 hours I had realized more or less only one spools of filaments , and in many joints the filament wasn't good.
I hope that someone will create a tool for automatic splice the filament soon.

[how can I use the remaining filament from material station?]

5 hours ago, Dim3nsioneer said:

Depending on the material it can also be used for the periodic print core cleaning (light PLA).

Thanks for reply, but the material is CPE for example or Tough PLA, and there are many meter of filament, more than one spool.

Usually I don't print with PLA, I prefer more technical material. 

I think that one option could be, insert the pieces of filament after disconnect the material station directly in the infeeder in the back of the printer for print a small parts.
What do you think about?

 

[how can I use the remaining filament from material station?]

HI, I use the Ultimaker S5 pro bundle since one year, and now I have many pieces of filament of the same material.
The pieces are more or less 2 meter long.
I'm sure that I cluster the piece of filament i can create a new spool ore more. Exist the possibility of use this pieces without weld the pieces?
Otherwise exist one sicure method of weld the pieces?
I tried to weld, but isn't easy, and I fear that the filament could broke into material station and damage it.

[Ultimaker S5 - Crash after printing?]

Ciao @PeterWhite76, I don't thinks that the problem is caused by warping in my case, because I have print the same parts and after update the firmware I had the problem, after update with the new one firmware the problem was fix. But now I configured the printer for update of Firmware stable and not latest.

[Stop fan air manager]

Hi,

Is possible stopped the fan in air manager? 

If I take of the cable the printer don't work. I checked into cura software but I don't saw the correct button. I see only Chamber loop fans, but it is already unselect.

Thanks

[Ultimaker S5 - Crash after printing?]

Hi, @Nicko_Airbus I had the same issue, with firmware 7.0.1, after update with 7.0.2 I don't see this problem.

But I'm not sure that the problem is the firmware. I checked all the parameters in the printer menu, and in the future I won't use the option "latest firmware". 

 

[Supporto per modelli di stampa]

ciao @ale_maker ho visto solo ora la tua richiesta, ecco un immagine esplicativa. 

[Componenti in pressione]

Ciao, interessante problematica, ho stampato parecchi materiali, ma non ho avuto esigenza di contenere aria in pressione. Probabilmente il PETG dovrebbe essere sufficiente, dipende anche dallo spessore delle pareti che ha il tuo pezzo. Se hai già risolto aggiornaci sul materiale usato.

 

[non trovo profilo stampante nella lista]

Ciao, se non trovi la tua stampante nella lista probabilmente non ha un profilo da caricare. Se vuoi usare cura lo devi settare manualmente, creandoti un profilo generico e andando manualmente a dargli i valori corretti.

[Supporto per modelli di stampa]

Ciao @3dgeneration in cura è possible aggiungere diversi plug-in tra cui quelli per creare dei supporti di forme diverse in maniera manuale. 

 

[Help for read the .CSV report from the printer]

Hi, I have a S5 pro bundle and I would save the printing data from the printer.

I would collect the quantity and type material I have printed from direct link with printer.
If I save the data from report through my account I don't see the column "job_material_grams_1" and "printer_material_grams_1" ecc.

If I save the report and I open it in Excel, I can see many columns, and for me is not clear what are all columns.

Exist a guide for explain the value for columns?

For example going to filter the column "status" with finish, I have all print that was finished correctly, but I don't understand what columns must I see for take the weight.

I attached the example .CSV report with only the title of the columns, because I don't know if there are non-shareable data.
Thanks

Report Ultimaker S5.zip

[Post your latest print!]

Hi, form my project "automatic shutters" I have studied a motor gearbox very cheap and the case is printed with S5 in CPE+. https://youtu.be/B2EWamvndWk

 

In the same time I have modify the baby motor with two motor and a new battery pack with lithium cells, but one of gear in a gearbox was broken and I trying to print it with technical different material, but in final I did a mix with a print gear and a metal gear. https://youtu.be/WH3fH85vcqo

[Test ingranaggio materiali tecnici con stampa 3D con S5]

Ciao, è da un po' di mesi che cerco una soluzione per un ingranaggio testando vari materiali tecnici, come Tough PLA, Durabio, Nylon, Policarbonato e CPE+ finalmente ho trovato una soluzione perché il doppio ingranaggio si rompeva sempre nella parte più piccola, ma ho dovuto fare un mix tra la stampa 3D e un altro ingranaggio in acciaio.

La stamapante che sto usando è una ultimaker S5, non ho provato con materiali caricati perché attualmente non ho l'ugetto C-C necessario per quei materiali. 

In questo video trovate i vari test.  https://youtu.be/WH3fH85vcqo

Saluti

Marco

[Problem with print core B-B]

Ok, I understand, in fact I put the spool in a vacuum bag with a silica gel bag.

Before reusing the spool, I will put it on the heat bed.

Thanks for your valuable help.

 

[Problem with print core B-B]

Thanks @ gr5 for your help. Now I have bought the vacuum bags for spools. The PVA and Nylon are in vacuum packed.
Next time I try to clean the print core B-B, because now I'm using the breakaway Ultimaker with A-A print core.

 

[Different height filament]

Hi, see this thread. 

I thinks that is the same problem. Cura 4.9 is the problem.

[problem fix in real time, it is possible?]

Thanks for your reply.

I think that the system used for see the "spaghetti" ( I'm Italian and I like pasta), is a free application can you manage through the code for check everything's, in this case the "spagetti".

I think that this idea is very interesting and that push the big companies to adopt a vision software for check the correct print.
I hope that soon we will come to print with all material in the super easy mode.

[Problem with print core B-B]

Yes, I think that the PVA have absorbed a lot of water though the spool is staying always in material station.

I will order a vacuum kit for PVA and other material. I read in this forum that is more correct put in the material station the PVA material only if will be used.

For clean the print core B-B

I see the message that the S5 tell me, and tell that I can used two tipe of material or PLA or clean filament, but I remember that the printer vendor was very clear that the B-B print core is only made for PVA. It is not possible to extrude the PLA otherwise it will be ruined.

 

[problem fix in real time, it is possible?]

Is there a system that monitors the piece layer by layer during printing and that can modify the print settings to correct any errors in real time?
such as the lambda probe for engines, or many other systems controlled in real time.
Machine vision could be used.
What do you think?

[Problem with print core B-B]

Thanks for reply.

Yes I used cura 4.9, in fact before start print I seen the PVA not in correct position, but when the PVA was arrived in position not worked very well. 

I thinks that there are 2 problems. The first the bug on cura 4.9 and the second the print core B-B

[Problem with print core B-B]

Hi, during the last print with S5 with material station and air manager, I have been some problems with print core B-B for PVA material.
The PVA didn't out very well for the firs time so I tried to reprint the piece, after 4 hours the printers was stopped with one error (https://support.ultimaker.com/hc/en-us/articles/360011706239-ER65-Flow-sensor-error), but after check the error the printer have finish the piece correctly.

Now, I want clean the print core B-B, but I don't sure that I can used the PLA material in this print core.

How I can clean the print core B-B? I can used PVA material or PLA?

thanks

Marco

[Is it possible to add NFC tags to generic material?]

During a print, I have finish the Ultimaker orange PLA ribbon and I have try to use a general PLA to finish the print, I have take the NFC from original ribbon and I have applied on the Generic ribbon, the printer has finished printing successfully.