conny
-
Posts
16 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by conny
-
-
Hi, I'm looking forward for the possibility to get into 3D Printing with this combination of the Ultimaker 3 and ColorFabb like filaments, with metal, so I'm looking forward for the solution...
It took me some time, but i get it to work :-)
If you want to print with two "foreign" Materials (as a dual print) and do the workflow Zwakie suggested, you'll get the following message from your printer: "This print job is not suitable for this printer - Err 26"
So the printer will NOT start the job....
What you have to do is to cheat Cura and the printer :-)
In Cura you have to pick up for the printcores one of the 5 Materials (eg. CPE) and modify it in the section "Material" on the right side - like printing temperature, build plate temperature a.s.o. so the it has actually the parameters of eg. Bronzefill. When you select the material on the printer it has to be the same you choose in Cura (eg. CPE).
It's not working when you add a new material to the list in Cura and select that for your printcore and slicing - then you'll get the ERR 26 message.....
hope it helps,
Conny
-
1
-
-
You can simply ignore the warning and go ahead with printing.
I did all the things you discripted above on Cura / Printer. When i got the warning on the Printer and tried to ignore it, the Maschine didn't started the print!!!! That's why i began this conversation....
-
Thx for your reply :-) But when i load the material on the Printer i have to make a choise (in the display of the printer) and there are only the 5 Ultimaker materials (if they have no Chip).
I tried to load HT and then i choose on the Printer one of the 5 material, in that case ABS. When i did the slicing in Cura i selected my new material Profil for HT and saved on the USB stick. When i put this stick on the Printer and select the gcode the Printer will not accept the in cura prepared material. It has to be the one i choose on the Printer.
So what to do now??????
-
Hi,
my new UM3 arrived and i'm quiet happy with it, but i have one big Problem. I use a lot Material from Colorfabb eg. Bronzefill, HT, nGen Flex... So i generated many new Material Profils in Cura 2.3.1 but didn't find a way to import these new Profils on the Printer.
The UM2 has an Import function, so it's very easy, but there is nothing like that on the UM3. Did i miss something?????
bests,
Conny
-
@emilio2: no changings of the firmware or printerhead - just the Bowden tube and feeder :-P
-
I'm using Roberts Feeder - so i can Change the Tension easy when i use the 1.75 or 2.85 Filament :-P
-
@Neotko: i used a 2 component glue
-
@Neotko: I used this because i found these things at home, otherwise i would have bought a new smaller PTFE Tube. Just the end at the stepper motor is glued and it has the same length as the original tube.
-
The smaller tube is just inside the original one (my spare part).To fix these together i used some glue and then there is no additional movement..
So if i want to swap the Filament i just change the tube.
Conny
-
-
Hi, i had the same problem with the "Heat Error" with Cura 14.12.1. on my UM2. So i had a look at my hot end and the temp. sensor and everthing looks fine. But i don't give up and found the solution. Problem was the fan duct - i used the one by venkel V6, which did a good Job so far. But as a switched back to the original one, the Error was gone :-P
So check you fan duct - if you don't use the original one. This may cause the issue.
bests,
Conny
-
Hi rustyw,
thank you very much - i'm running now the 1.75mm Filament with the original bowden tube but with a flow of 300% and that worked quite good. In the next couple of days i will give your setting a try, as soon as i get the 2mm tube.
-
Hi,
mit einer schönen Schicht Prittstift und Bett bei 70 Grad hab ich keine Probleme mit der Haftung.
Ich hab ein ganz anders Problem mit dem XT und zwar bei Überhängen auch mit Support gibt es nur eine ganz unregelmäßige Oberfläche in den ersten Schichten.
Parameter sind: Temp:. 240 Nozzle) / 70 (Bett). Fan 50%, Schichtdickt 0,1 Geschwindigkeit: 40
Sonst bin ich total vom dem Filament begeistert, wenn nur dieses Problem nicht wäre...
Kann mir da jemand weiterhelfen?????
LG, Conny
-
Thx for the link with the new Feeder - I'll give it a try.
Hope it works ;o)
-
Hi,
i have from my other 3D Pritner (now: out of order) a lot of 1.75mm Filaments left and i don't want to throw i away so i'm looking for a way to use it on the Ultimaker 2.
Does have anyone experiences with it? What do i need to change - on the Printer or the Software?
best wishes,
Conny
-
1
-
New Material on Ultimaker 3
in UltiMaker 3D printers
Posted
I think Daid has some issues to fix, especially for the Material concept on the UM3. The design and idea is really nice, but it's not properly working now....
I really hope that changes soon :-)