-
Posts
35 -
Joined
-
Last visited
-
Days Won
1
Content Type
Forums
Events
3D Prints
Posts posted by Pena
-
-
Hey Guys
Now with everyones help, I understand the noise level results of the Level Sensor Test shouldn't exceed 8.0
Your help is much appreciated!
Dan
- 1
-
-
Thanks Guys!
With all the information everyone has provided, I've narrowed it down to the capacitive sensor board.I found a Fan wire crossing directly over the PCB, the fan wire was being squeezed between the heating element wires of the print core and the PCB. I moved the fan wire, ran the test Level Sensor Test aging with the following results.
Again thanks!
Dan
-
Hey Guys,
I've had an issue off and on in regards to leveling results on my S5.
I thought my leveling error had something to do with the magnets I installed on my build plate however, the error is repeated with a glass build plate and no magnets.
I have replaced both AA and BB nozzles with new nozzles and cleaned the nozzle seating areas.
I have completed the manual level procedure and leveling sensor test several time. When I reboot the S5 and repeat the manual leveling the error returns. Once I remove the New Print Head Nozzle and reinstall the same new nozzle the S5 will randomly level and start working.
My question is: how is the information received from the Leveling Sensor Test used or how can it be helpful?
Dan
-
-
I received the following for a toy I created using my Ultimaker S5!
Congratulations! You and your product, FireFly (Kinetic Energy Toy), have been selected to be showcased at Toy Fair’s Creative Factor Inventor Day!
I will reveal the design during the event, Tuesday, October 3 at the Javits Center in NYC from 10 AM – 1PM,!
Thank you UltiMaker!
Dan
- 1
-
Does anyone know of a return option to the previous task in the printing cycle for the S5?
You know, the task that was going fantastic just before it went dumfounded and didn't print anything!
-
You are awesome! I'll give it a try Boss!
-
You might also research Quality - Layer Height in Cura material settings.
-
-
Have you tried reducing your print seed and keeping your TPU filament dry?
-
It looks like your print is sheering apart, have you tried slowing the print speed and keeping the filament dry?
-
Verify your filament is kept dry, you can weigh the material after opening the material for the first time. Also when not in use I store 4 rolls of TPU material in 2 lbs. silica gel beads.
-
I get this issue when printing translucent materials, I disabled the flow sensor in the printer settings.
-
The printer is showing up however the Camera function isn't available. The only access to the printer's camera is by way of using DF.
-
On 7/7/2022 at 2:04 AM, HB9GIM said:
Where can you turn features on/off? I can't zoom, or rotate Bed with the mouse. Both in Cura 5.0 and now the same in Cura 5.1
I firmly press and drag two fingers on my Mac track pad, this allows me to rotate the bed. I lightly press two fingers and drag to zoom. I hope this helps.
-
Hey Guys, So I followed each line item as instructed per error ER31, nothing worked "very frustrating"!
I decided to remove the heating element from BB nozzle 2 and replaced just the heating element from an extra print core AA. All is working perfectly!
I've been looking for a replacement heating element for my BB print nozzle 2.
My preference is to purchase only the heating element.
Does anyone know if I am limited to purchasing the entire BB print core/nozzle?
Is it possible to purchase just the BB heating element, if so where and is there a part number?
-
Hey guys,
Is anyone having issues with the Cura software connecting to the Ultimaker S5 printer? I see my printer is available on the digital factory in standby, but Cura won't locate it. I have the S5 attached using my Ethernet and it provides an IP address. So I tried adding it using the IP and it will snap a quick glimpse of the S5 then disappear. I was finally able to get it all connected after several reboots.
-
Customer service responded immediately and I am pleased!
Thank you!
- 1
- 1
-
I’ve sent a request to customer service to help send both of my orders in one order.
-
Thank you, I’ve placed my order!
you’re awesome! -
1 hour ago, Smithy said:
I am sure @fbrc8-erin can help you.....
Thank You!
-
Thank You but Digikey is out of stock
-
Has anyone found a U.S. supplier for the Ultimaker S5 fan, I need a replacement?
SUNON MC35100V2-000U-A99 M Series 35 x 35 x 10 mm 5 V 6.5 CFM 0.38W
S5 Leveling Sensor Test
in UltiMaker 3D printers
Posted · Edited by Pena
Hey Cyriaquer,
I took your advice and removed the Radial fans, see attached photos. The fans were horribly dirty which I think altered the fan blades by placing them out of tolerance or out of balance. I used my shop air compressor to carefully blow the blades and being careful not to over clock or exceed RPM rating and break the blades. I then used a brush to rub off stuck on dust and gave them a final compressed air cleaning. I did this to the fan support housing as well.
I put everything back together and voila the printer is working. I've completed two prints back to back with no issues.
I also ordered two knew radial fans (Print core side fans) or Model Cooling Fan Part #UM3/UM3X/S5/S3/S7 for my S5. and will replace the old fans if I have anymore leveling issues.
Thank you for your awesome advise and support!
Dan