Jump to content

Ultimaker original plus eichen


miro-laserdesign

Recommended Posts

Posted · Ultimaker original plus eichen

Habe den Ultimaker Original Plus zusammengebaut. Die gedruckten Teile sind etwas kleiner als das 3D-Modell. Beim Ultimaker 2 stimmt die Größe ziehmlich genau. Suche im Internet eine Anleitung für das Benutzermenü des Ultimakers Original Plus. Unter "Control - Motion" im Benutzermenü denke ich, kann ich die Werte ändern, um am Ende mein Modell mit den richtigen Maßen gedruckt zu bekommen. Eine Anleitung wäre hilfreich, damit ich nicht raten muss, welche Werte geändert werden müssen. Im Internet kann ich keine ausführliche Anleitung zum Benutzermenü finden.

  • Link to post
    Share on other sites

    Posted · Ultimaker original plus eichen

    Wer sucht, der findet. Für alle, die es interessiert:

    Motion

    Acc

    The standard is 3000, it allows you to adjust the acceleration speed.

    Vxy Jerk

    Vxy Jerk is the acceleration of the acceleration

    Vmax x

    The maximum speed in mm/s

    Vmax y

    The maximum speed in mm/s

    Vmax Z

    The maximum speed in mm/s

    Vmax E

    The maximum speed in mm/s

    Vtrav min

    This is the minimum distance to travel

    Vmin

    The minimum speed in mm/s

    Amax x

    The speed in which the motors can accelerate.

    Amax y

    The speed in which the motors can accelerate.

    Amax z

    The speed in which the motors can accelerate.

    Amax e

    The speed in which the motors can accelerate.

    A retract

    The acceleation speed in which you allow retraction to operate

    X steps-mm

    The accuracy the steppers can make the motors move in.

    Ysteps mm

    The accuracy the steppers can make the motors move in.

    Zsteps mm

    The accuracy the steppers can make the motors move in.

    Esteps mm

    The accuracy the steppers can make the motors move in.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...