Jump to content

ffreak

Dormant
  • Content Count

    37
  • Joined

  • Last visited

Community Reputation

1 Neutral

Personal Information

  • Country
    BE
  1. Hi, i'm back. Was very busy last days. Indeed, the room was very hot ... (heatwave). Next week I will figure out what went wrong taking all remarks in mind ... My supplier is willing to do the repair ... but I want to do it myself if possible. I'll share my solution when UM is fixed.
  2. We're talking about a UM2. Manually moving the buildplate up and down is no problem. Problem is: at some hight (different from print to print) the printing continues at the same hight. And most strange of all: the printing follows the model ... The plate doesn't lowers all of a sudden during the print. There is no clog initially but after some laps printing at the same hight a clog is growing at the nozzle.
  3. yo, tried 3 prints. At different hights buildplate stopped lowering. So print continued at same level (pic). After third try-out print got error message: x-axis stuck....
  4. Hello, today my buildplate doesn't lower anymore ... Tried to make 2 prints and each print: the buildplate got stuck at a different hight ... Yesterday everything was ok .... What could be wrong? thx
  5. Yo skinny-kid, thx for your reply. Posting the file is rather difficult because it concerns a commercial prototype. After posting this problem I've shut down the printer, restarted and problem seemed to be solved. Really don't know what happened ... but everything goes oké now. Only difference between first print yesterday and second print: the first print cura didn't positioned the print in the center of buildplate. Starting the second print cura perfectly positioned the print on buildplate. Anyway thx for your reply grtz
  6. Hello, Started a print this morning and my support isn't correct (in comparison to yesterday). See pic. What goes wrong? Can anybody help me please? thx[/media]
  7. ffreak

    d-limonene

    thx JohnFox for the links
  8. ffreak

    d-limonene

    Hello, should I use d-limonene 99.5% purity or is 95% purtiy enough to dissolve hips? Do I use the limonene pure? thx
  9. xbrain666, what about the first printlayer: slow printing? extra wide printing? or the same as the other layers?
  10. yo Nicolinux, thx for your reply. What filament are you printing with? I'm printing hips.
  11. I don'k know what to choose: Dimafix or Kapton tape to solve may heated bed adhesion problems ...
  12. Yo gr5, thx for your message. And yes, I have encountered your remark. My advice: remove the hips directly when printing is done: each time. Compared to cleaning a nozzle, it's no effort loading the filament before printing . The first testprints with hips were a dissaster: nozzle clogged each time. By removing the hips after each print I have no problems anymore. Furthermore, when removed the hips spool, I put the spool in a box with moisture absorber ...
  13. hello stu_le_brew: indeed. As my UM was brandnew I was almost afraid of touching it.Changing Olsson was allready a challenge, replacing the sensor and later on the heater were very scary situations to me. The new heater is indeed a great improvement.
  14. Inderdaad, ook mijn leverancier heeft me een 35W element toegestuurd: geen enkel probleem meer. Maat toch een tekortkoming van Ultimaker vind ik dat men dit niet zo kenbaar maakt.
  15. ok fijn om te horen ben nu met pet bezig en mijn feeder slaat over ik krijg niks goed er uit ik denk dat ik maar eens met de mensen van de winkel er over ga hebben Heel veel ervaring heb ik nog niet. Maar toen ik overschakelde van PLA naar HIPS heb ik mijn feeder moeten afstellen. Het wiel greep zich steeds vast in het zachtere HIPS. Nu heb ik geen problemen meer hiermee. Als je werkt met een UM2= naast de Bowden tube zit bovenaan de feeder een vijsje ingewerkt. Hoe meer je naar links schoeft hoe groter je eigenlijk de doorstroommogelijkheid maakt, hoe minder hard de feeder op het filament drukt ... Of misschien staat je feeder te los: gewoon bijregelen door naar rechts te schroeven. ik heb een robox gehad voor mijn UM2 das wel een groot verschil .maar heb net contact met gehad met de winkel waar ik hem gekocht heb en die heeft me een actomic clean laten doen en heb de kop ff los gedraaid en weer vast en de slang voor filement weer op nieuw er in gezet tot nu toe geen probleem hoop dat het goed blijft gaan Je nozzle zat verstopt waardoor je feeder niet meer efficiënt kon werken ... heb ik ook reeds voorgehad. Goed te horen dat je weer op dreef bent.
×
×
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!