Nederlands

273 topics in this forum

1. Metaal achtig tikkend geluid Z-as

   By Marijn73, Tuesday at 09:37 PM   

   • HELP
   • UM3
   • 5 replies
   • 36 views
   • 
   • ahoeben
   • 50 minutes ago

2. Probleem met filament

   By juflaurab, yesterday at 07:38 PM
   • 3 replies
   • 27 views
   • 
   • geert_2
   • 4 hours ago

3. um2 + crashed

   By gizmo999, November 28
   • 4 replies
   • 77 views
   • 
   • gizmo999
   • Sunday at 07:14 PM

4. Afmetingen blok in het bed

   By Ik-ben-Jerry, December 4
   • 2 replies
   • 54 views
   • 
   • Ik-ben-Jerry
   • December 5

5. Probleem met Cura

   By Hovestadt, October 3
   • 11 replies
   • 294 views
   • 
   • Hovestadt
   • December 4

6. Probleemmet printen

   By Ik-ben-Jerry, December 2
   • 1 reply
   • 59 views
   • 
   • Ik-ben-Jerry
   • December 3

7. letter j van mijn naam gevallen

   By Ik-ben-Jerry, December 2
   • 8 replies
   • 85 views
   • 
   • Ik-ben-Jerry
   • December 3

8. UM 5 of 3?

   By 3dcase, November 13   

   • UM3
   • UMS5
   • 9 replies
   • 154 views
   • 
   • SandervG
   • November 21

9. Temperatuur blijft tijdens opwarmen hangen op 95%

   By arlee, November 3
   • 2 replies
   • 112 views
   • 
   • rien1959
   • November 8

10. UM3 bevroor bij eerste print en daarna dood, wifi probleem?

    By The_real_Oscar48, October 22   

    • HELP
    • UM3
    • 2 replies
    • 175 views
    • 
    • The_real_Oscar48
    • October 29

11. Z-as verplaatst pas na X-Y beweging volgende laag

    By Jeroen-APD, October 25
    • 0 replies
    • 80 views
    • 
    • Jeroen-APD
    • October 25

12. Nozzle probleempje

    By PeerKaan, October 18
    • 5 replies
    • 134 views
    • 
    • PeerKaan
    • October 25

13. Welke soorten filament?

    By PeerKaan, September 6
    • 20 replies
    • 378 views
    • 
    • PeerKaan
    • October 22

14. De Anet A8 gevaarlijk!!!

    By 3drob, November 13, 2017
    • 4 replies
    • 951 views
    • 
    • 3drob
    • October 19

15. Ultimaker 2+ 'bevroor'

    By RaimonElctrncs, October 13   

    • HELP
    • 1 reply
    • 126 views
    • 
    • geert_2
    • October 15

16. Onderdelen heated bed UMO(+)

    By PeerKaan, October 3
    • 4 replies
    • 143 views
    • 
    • PeerKaan
    • October 3

17. Ultimaker PLA zonder nfc chip

    By RaimonElctrncs, October 1
    • 5 replies
    • 143 views
    • 
    • Job_van_gennip
    • October 3

18. Cura 3.4.1 instelingen voor DIY Prusia i3 ?

    By 3drob, September 24
    • 6 replies
    • 155 views
    • 
    • PeerKaan
    • September 27

19. Een beginner, hulp nodig met "eenvoudige" software voor 2 kleuren

    • 1
    • 2

    By Kevin77, June 7   

    • HELP
    • UM3E
    • 39 replies
    • 1,019 views
    • 
    • Kevin77
    • September 27

20. Firmware UM2+

    By RaimonElctrncs, September 24   

    • HELP
    • 2 replies
    • 163 views
    • 
    • RaimonElctrncs
    • September 27

21. Print ontwerp niet netjes door support(cura )

    By RicardoB101, August 19
    • 6 replies
    • 242 views
    • 
    • RicardoB101
    • August 23

22. Extruder/nozzle lijkt verstopt

    By denkol, July 13, 2014
    • 10 replies
    • 6,941 views
    • 
    • BartV
    • July 23

23. Cura print niet correct in Ultimaker 2+.

    By Tremonti, July 20
    • 4 replies
    • 209 views
    • 
    • Tremonti
    • July 21

24. Cablebeak

    By Cablebeak, July 17   

    • HELP
    • 0 replies
    • 181 views
    • 
    • Cablebeak
    • July 17

25. 3d pen lost wax?

    By marcogiers, June 21
    • 11 replies
    • 336 views
    • 
    • geert_2
    • June 28