qwerty8224
-
Posts
64 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by qwerty8224
-
-
Again broke Cura 3.4 (((.
Printing PLA support PVA Mark2Tweaks.py does not work.
Command Ultimaker ???
-
tinkergnome
Thank you for not forgetting about this wonderful project Mark2 ....
installed Mark2Tweaks.py (cura-3.2-resources) and my 2 nozzles became just fine to work with. Stopped to visit the place 1 nozzle all super I'm very happy)))))
And again thanks to everyone who took part in the development of this project YOU gave us the opportunity to get acquainted with two-tone printing at minimum cost. ))))- 2
-
correct please definition of nozzles for Сura 3.4
[values]
machine_nozzle_size = 0.6
machine_nozzle_tip_outer_diameter = 1.25
coasting_volume = 1.36
speed_wall = = round (speed_print * 4/3, 1)
speed_wall_0 = = 1 if speed_wall <10 else (speed_wall - 10)
speed_topbottom = = round (speed_print / 2, 1)
then what is highlighted should be removed .... I have to Cura 3.4 works.- 3
-
as always, I like everything))) but it's a pity that many excellent fixations from smartavionics did not get into this assembly (((.
thanks to everyone who takes part in the development. -
Thank you.
Then I will look for the best results with different types of plastic. -
I tried this function and it's just great. This is what we have so long lacked ....
Thanks againYou are moving in the right direction))) and all your efforts I think highly appreciated by the community. At least me))) Continue to please us further)))
Is it worth waiting for the improvement of this function? -
Сura 3.2 2 nozzle visits the place of the 1st nozzle ?
-
Very very good )))
-
smartavionics
I want to say thank you for your contribution to Cura you are the only one who optimizes the algorithm and not just writes it)))))
And you do it very very well.
It is interesting to know how much% of the installation has increased Сura 3.0.3
with the function entry"Optimize Wall Printing Order" )))))
Good luck )
-
Thank you...
-
... also the new postprocessor for "Correction of hole sizes, cylinder diameters and curves" sounds really interesting - will give it a try later on...
Where can I see this ???
-
The error appears when there is nothing to optimize)))
But there is a check mark for optimization.
I will not disable this feature .... no way
I will be a good tester))))))))
-
Cura 3 beta very very good.
Thanks to everyone who takes part in the development Сura .
I want to say a special thank you third-party developer "smartavionics" for the function Optimize Wall Printing Order .... and his other achievements.
Sorry for my English (
Thank you again from version 2.1 to 3.0.0 done a great job that deserves praise.
- 3
-
My printer began to print much better)))
-
New Firmware 17.6
Thank you tinkergnome
- 1
-
zerspaner_gerd
Horror:D:D:D
-
foehnsturm
Thank you for your efforts ... and I wish you a good rest. You and your team have done an excellent job.
- 2
-
This is not a problem with the Gcode startup (
I think this is the firmware ....
Although it is necessary poprobyvat)))
I could not solve the problem through the starting gcode (
-
chiz
Print area problem by Y play with the print area Cura and printer
-
Чиж
Print area problem by Y play with the print area Cura and printer
-
AFter doeing this:
Cura check: Travel->layer start x/y and set it to something like 100.0/50.0
My error Сura 2.5 is solved ;-)
-
Can anyone help decipher these values Printing zones
[[-115, 112.5], [-10, 112.5], [-10, 72.5], [-115, 72.5]],
[[115, 112.5], [115, 72.5], [15, 72.5], [15, 112.5]],
[[-115, -112.5], [-115, -87.5], [ 115, -87.5], [ 115, -112.5]
[[-115, 72.5], [-97, 72.5], [-97, -112.5], [-115, -112.5]]
-
I want to say thanks to all developers Mark2 ....
Ultimaker 2 Aluminum Extrusion worker.
The first 2 printing is very good)))))
-
Cura 2.5 incomprehensible steps in the left corner ?? ???
Cura 2.4 all OK
Introducing Ultimaker Cura 3.5 | Beta
in UltiMaker Cura
Posted
thanks to everyone who took part in the development ...
my prints have become even better))) you make me happy)))))))