limburgmetaal
-
Posts
34 -
Joined
-
Last visited
Content Type
Forums
Events
3D Prints
Posts posted by limburgmetaal
-
-
Hi Geert,
Thanks
But the "flat" bit on the bottom is the marking area and the hole concept of the print.
On this you can write that it is "a 9mm Drill" and store it.
If you need the drill you will have it right away and don't need to measure the tool anymore.
The two arms are a bit spring loaded to hold the "flat bit" -
On 10/7/2021 at 9:20 AM, Carbon said:
i tried this, but is not giving the result that i was looking for.
-
-
Hi
I have a ultimaker3 and work normally fine.
but i have no a problem that the PLA core is not feeding anymore.
Initially i thought there was something with the reel as the feed wheel was grinding in the core.
Changes the spool and again it happend.
2 Spools and 3 product that on the exact same spot start to get faulty.The feed unit has been opened to check, cleaned of small dust, knurling on feedwheel is fine, main gear wheel seems fine.
infeed of new material goes smooth
Anyone who has a clue? -
thanks Sander
i will give it another try
Maarten
-
It there someone who succeded in making a working wrench?
i have tried several on the web found but non was working
the offset possiblity was used and that made it a little bit better, but still not working
below picture are top and bottom side
bottom side is very poor!!
Machine UM3
Nozzle 0.4
Layer height 0.1
material tried: PLA and ABS
Support either PLA or PVA with the ABS
-
-
will thinnen layers be better or worse?
-
-
I have both cura and s3d, if i can help than let me know
-
have you tried to make the same print with an other slicing program as well
cura and s3d? if so this will eliminate the error in a Gcode
-
Can you glue 2 pieces of a pla printed part together?
I tried to use Loctile 415, but that is not working
-
I put it under the tap, 2 minutes cold water and it is loose
-
how can you see if there is a new firmware available and what your current firmware issue is?
-
I can not see where you can save your programm setting.
The machine setting can be save as profile, that is easy.
but if you have a builtup of several STL files on your table, all lined out that there is maximum parts and still good space, then i can't save that.
is this not something that more people would need, or have i overlooked something?
-
You might want to adjust the horizontal expansion so the parts don't intertwine. There's a Cura option for that that I forgot the name (ofc is a hodden option that needs to be unhidden).
thanks, i never know that there was so much hidden "underwater"
do you give a possitive value or negative value to make the holes bigger?
i assume a +1
or is this trial and errow combined with a bit of good luch
-
is there anyone who made these adjustable wrenches that work?
i tried today two different versions but both are stuck and can't get any movement
-
Nice, I was thinking about building a Full enclosure for heat and noise purposes. Do you think some ventilation is needed? I worry about getting too hot inside.
some ventilation will be needed, but mostlikly the main purpose is to stop the draft.
as the bed and the extruders are temp controlled they should be able to cope with the hood
-
-
I can't find anywhere to swith of the lights on the UM3,
the tune option during printing is not listing it.
the reason to turn them down/off is that i like to print overnight
any idear?
-
-
if i try the PLA/PVA version,
would the following setting be ok?
PLA 195°
PVA 220°
Bed 60 °
-
hi Sander,
Bed leveling done through the setup with the card
As well as XY setting calibrated etc
PVA setting was mentioned, 220° and 80 on the bed.
I will try tomorrow the PLA/PVA as it looks that ABS/PVA is a non-starter
the printer is standing in a normal office, we have put a cloth over the top with the last two attempt to eliminate the draft and loss of temp.
Glue, we used the 3dlac spray
-
Flexible material
in Improve your 3D prints
Posted
that makes sense!, thanks, never tought about it this way.
Will try it over teh weekendZ
Thanks!