Jump to content

Magic blue tape trick


Recommended Posts

Posted · Magic blue tape trick

Hello,

Just wanted to share what I found working good if you don't have a heated bed: I used 3M 3434 blue tape. I primarily ordered it because it was 5cm wide, and I was tired of replacing the narrow stock blue tape after almost every print.

Following an advice found elsewhere, I sticked 2 layers (perpendicular) of this tape on the stock bed, and did not have to replace this tape after a lot of prints (actually, I NEVER had to replace it, because after some time I got an heated bed :D )

I don't know if it's the tape or if it's due to the two layers (probably providing some elasticity in case the nozzle is too close to the bed) but the first printed layer always sticked well, and it was also a lot easier to detach the object after the print, with no damage to the tape.

This will work only for PLA, not for ABS.

My 2 cents

JP

  • Link to post
    Share on other sites

    Posted · Magic blue tape trick

    For completeness, i should add that i was doing a quick wipe with acetone before each print.

    I forgot to tell, because I was also doing this with the stock blue tape, and continue to do it on my heated bed borosilicate glass

    JP

  • Link to post
    Share on other sites

    Posted · Magic blue tape trick

    Just tried a first print with this, here's some things I noticed:

    - PLA sticks great.

    - When I pulled the finished print off, it did pull up some of the tape off the top layer. But it didn't destroy it, it was pretty easy to smooth it out.

    - I got way less "grilled cheese corner" on prints (where it curls up at corners).

    - Prints came out great despite the bed having poor calibration.

    I have a bunch of things to print over the next couple of days, so I'll be able to give it a good test. :D

  • Link to post
    Share on other sites

    Posted · Magic blue tape trick

    Great!

    Did you just put two layers of stock blue tape, or use 3M 3434?

    May be the nozzle is too close to to the bed, pushing hard pla on tape, thus causing over adhesion. You may try to increase a little bit the Z height.

    JP

  • Link to post
    Share on other sites

    Posted · Magic blue tape trick

    Actually, I used some 3M tape, same as stock just wider. I'm going to pick up some 3M 3434 today and try it out.

    For sure the nozzle was off; I mentioned that my bed was poorly calibrated at the time. I was just so surprised to see it still print fine.

    Tonight and tomorrow I'll try with 3M 3434 & a calibrated bed. :D

  • Link to post
    Share on other sites

    Posted · Magic blue tape trick

    I *think* that 3434 sticks less than stock, so you should be able to detach the part more easily after the print.

    The drawback may be that you get more warping as it sticks less, but i did not notice any PLA warping with 3434 (YMMV).

    Please, let us know.

    JP

  • Link to post
    Share on other sites

    Posted · Magic blue tape trick

    Nothing new to report as I haven't found any 3M 34343 at any hardware stores near where I live.

    Do you have a link to it? I tried searching for it on 3M's website and the link it found wasn't working.

  • Link to post
    Share on other sites

    Posted · Magic blue tape trick

    I got it on eBay (UK seller), here:

    http://cgi.ebay.fr/SCOTCH-3M-Detailers- ... 43b21e85c0

     

  • Link to post
    Share on other sites

    Posted · Magic blue tape trick

    another little tip.

    if your always printing small objects like key chanins or some thing like that.. mask up just the area under neath what you will be printing!

    i amount of times i remashed my bed and it looked super and clean and then one bold small model and the whole thing came back up and redone...

    it took me too much time to realise how stupid this was on my side and now i just mask up the areas i will be printing. saves me buckets of tape.

    Ian :D

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...