Jump to content

Weird 404 error every 3 minutes in the Event log...


cgosnell

Recommended Posts

Posted · Weird 404 error every 3 minutes in the Event log...

I am concerned with the following 404 messages showing up in the event log every 3 minutes or so:

  • Apr 01 18:13:05 ultimakersystem-ccbdd30052e1 python3[182]: 2019-04-01 18:13:05,919 INFO systemUpdate Comparing firmware 'stable' old version '5.2.8.20190320' with new version '5.2.8.20190320' with result: True
  • Apr 01 18:13:04 ultimakersystem-ccbdd30052e1 python3[182]: 2019-04-01 18:13:04,964 WARNING systemUpdate HTTP error 404 during updating of the update version strings for release type 'testing' from url 'http://software.ultimaker.com/releases/firmware/9511/testing/um-update.swu.version?current_version=5.2.8.20190320': Not Found
  • Apr 01 18:12:48 ultimakersystem-ccbdd30052e1 python3[830]: 2019-04-01 18:12:48,820 INFO timeEstimator getTimeRemaining() total_time 4:22:43 scaling_factor 1.000563029451881 compensated_total_time 4:22:51.875033 time remaining 3:57:51.134417 pure_cura_time_remaining 3:57:42.259165
  • Apr 01 18:12:48 ultimakersystem-ccbdd30052e1 python3[830]: 2019-04-01 18:12:48,306 INFO timeEstimator getTimeRemaining() total_time 4:22:43 scaling_factor 1.000563029451881 compensated_total_time 4:22:51.875033 time remaining 3:57:51.648284 pure_cura_time_remaining 3:57:42.773022
  • Apr 01 18:11:03 ultimakersystem-ccbdd30052e1 python3[182]: 2019-04-01 18:11:03,565 INFO systemUpdate Comparing firmware 'stable' old version '5.2.8.20190320' with new version '5.2.8.20190320' with result: True
  • Apr 01 18:11:02 ultimakersystem-ccbdd30052e1 python3[182]: 2019-04-01 18:11:02,453 WARNING systemUpdate HTTP error 404 during updating of the update version strings for release type 'testing' from url 'http://software.ultimaker.com/releases/firmware/9511/testing/um-update.swu.version?current_version=5.2.8.20190320': Not Found
  • Apr 01 18:09:01 ultimakersystem-ccbdd30052e1 python3[182]: 2019-04-01 18:09:01,361 INFO systemUpdate Comparing firmware 'stable' old version '5.2.8.20190320' with new version '5.2.8.20190320' with result: True
  • Apr 01 18:09:00 ultimakersystem-ccbdd30052e1 python3[182]: 2019-04-01 18:09:00,137 WARNING systemUpdate HTTP error 404 during updating of the update version strings for release type 'testing' from url 'http://software.ultimaker.com/releases/firmware/9511/testing/um-update.swu.version?current_version=5.2.8.20190320': Not Found

It seem that the system is looking to confirm a 'testing' versionof the firmware.

The front panel check of the latest firmware tells me that I have the latest stable version

I went logged into the printer in Developer mode and cleaned up any core dumps, etc.  And did an apt-get to clean up and update any software on the printer.

Also the system clock seems to be set on GMT, vs local time (CDT) US.

 

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
      • Ultimaker Cura 5.6 stable released
        Cura now supports Method series printers!
         
        A year after the merger of Ultimaker and MakerBotQQ, we have unlocked the ability for users of our Method series printers to slice files using UltiMaker Cura. As of this release, users can find profiles for our Method and Method XL printers, as well as material profiles for ABS-R, ABS-CF, and RapidRinse. Meaning it’s now possible to use either Cura or the existing cloud-slicing software CloudPrint when printing with these printers or materials
        • 48 replies
    ×
    ×
    • Create New...