Jump to content

Insert M80 prior to bed heating

Biff

By Biff
in UltiMaker Cura

 Share

Recommended Posts

Biff

Biff 0

Posted
Posted · Insert M80 prior to bed heating

Cura 4.1

G-code flavor: Marlin

How to cause M80 to place prior to Bed Heating

 

;FLAVOR:Marlin
;TIME:1014
;Filament used: 1.43077m
;Layer height: 0.3
;MINX:88.834
;MINY:96.542
;MINZ:0.3
;MAXX:130.024
;MAXY:123.458
;MAXZ:18.9
;Generated with Cura_SteamEngine 4.1.0
M140 S60
M105
M190 S60
M104 S190
M105
M109 S190
M82 ;absolute extrusion mode
M80 ;Power Supply On
G28 ;Home

    • Link to post
    Share on other sites
    obewan

    obewan 37

    Posted
    Posted · Insert M80 prior to bed heating

    You need to put the bed and extruder placeholders in the machine start Gcode

     

    eg

     

    G21 ; set units to millimeters
    G90 ; use absolute positioning
    M80 ;power supply on
    M104 S{material_print_temperature_layer_0} ; set extruder temp
    M140 S{material_bed_temperature_layer_0} ; set bed temp
    M190 S{material_bed_temperature_layer_0} ; wait for bed temp
    M109 S{material_print_temperature_layer_0} ; wait for extruder temp
    G92 E0.0 ; reset extruder distance position
     

    • Link to post
    Share on other sites
    Biff

    Biff 0

    Posted
    • Author
    Posted · Insert M80 prior to bed heating

    obewan,

    tkx, not only did that make the difference,  I went looking for and found the parameters listings.

    Didn't know it existed.

    Game On!

    Biff

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 1
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 16 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...