UltiMaker uses functional, analytical and tracking cookies. Tracking cookies enhance your experience on our website and may also collect your personal data outside of Ultimaker websites. If you agree with the use of tracking cookies, click “I agree, continue browsing”. You can withdraw your consent at any time. If you do not consent with the use of tracking cookies, click “Refuse”. You can find more information about cookies on our Privacy and Cookie Policy page.
Ultimaker Cura 4.4 connect to Octoprint,is it Possible?
Posted
· Ultimaker Cura 4.4 connect to Octoprint,is it Possible?
Are you sure you have a working network connection from your raspberry? Normally the Octoprint plugin finds running instances of Octoprint. So I would first check if your network setup is correct and the raspberry is connected to the network and got an IP address from your router. You can also check it you can connect to the Octoprint web gui via your browser.
If this is working and the plugin can still not find your instance, you can always enter the IP address manually in Cura to connect to it.
Posted
(edited)
· Ultimaker Cura 4.4 connect to Octoprint,is it Possible?
Hi Smithy, Thank you for your reply, I was about to call it a night, I did try everything, yeah rasberry had a network connection and had an IP address from router, yeah I was able to connect to the octoprint web gui. But , I think your reply made it work ..... lol. after reading your reply went back and switch on laptop, 3d printer and rasberry pi: everything looked fine, rasberry pi network connected , octoprint on my web browser connected to printer, so i went and open cura to have another go, and Guess what, ....... this time there was an octoprint instance to choose from, so , i think your message made it work ......lol.
My Ultimaker Cura is connected to Octoprint 🙂 . I have sliced a file and clicked print with octoprint to test, "it's working" printing as i write this message, I guess i'm staying up a little longer 🙂 . Thanks Bud.
Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more.
S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
(Sorry, was out of office when this released)
This update is for...
All UltiMaker S series
New features
Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
Recommended Posts
Smithy 1,144
Are you sure you have a working network connection from your raspberry? Normally the Octoprint plugin finds running instances of Octoprint. So I would first check if your network setup is correct and the raspberry is connected to the network and got an IP address from your router. You can also check it you can connect to the Octoprint web gui via your browser.
If this is working and the plugin can still not find your instance, you can always enter the IP address manually in Cura to connect to it.
Link to post
Share on other sites
inkaworld 1
Hi Smithy, Thank you for your reply, I was about to call it a night, I did try everything, yeah rasberry had a network connection and had an IP address from router, yeah I was able to connect to the octoprint web gui. But , I think your reply made it work ..... lol. after reading your reply went back and switch on laptop, 3d printer and rasberry pi: everything looked fine, rasberry pi network connected , octoprint on my web browser connected to printer, so i went and open cura to have another go, and Guess what, ....... this time there was an octoprint instance to choose from, so , i think your message made it work ......lol.
My Ultimaker Cura is connected to Octoprint 🙂 . I have sliced a file and clicked print with octoprint to test, "it's working" printing as i write this message, I guess i'm staying up a little longer 🙂 . Thanks Bud.
Edited by inkaworldLink to post
Share on other sites
Smithy 1,144
Thanks for the feedback!
I'm glad it worked.
Link to post
Share on other sites