Jump to content
UltiMaker Community of 3D Printing Experts

Strange effect in just one corner?

Claghorn

By Claghorn
in Ultimaker Cura

 Share

Recommended Posts

Claghorn

Claghorn 1

Posted
Posted (edited) · Strange effect in just one corner?

I'm trying to get cura dialed in on my old (but newly upgraded) solidoodle. If I print this single wall one bottom layer test cube I use a lot, in RepetierHost with slicr3 it comes out just about perfect. Copying lots of settings from slicr3 to cura, the same print in cura comes out perfect everywhere except one corner (where the bottom layer lines are really short). In that same corner the brim (which works fine in all the other corners) looks like the lines pushed up from the bed. Anyone have any idea what settings could be related to this? The compare.jpg has the slicr3 version on the left and the cura version on the right. The corner.jpg shows the bottom corner where things pushed up.  In case it matters, that corner is the corner where it initially started printing the bottom layer (it was front right on the build plate), the Z seam was the back right corner.

compare.jpg

corner.jpg

Edited by Claghorn
add info about bad corner
    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Go to topic listing

    • Our picks

      • Here it is. The new UltiMaker S7

        Here it is. The new UltiMaker S7

        MariMakes posted a topic in Official news,

        The UltiMaker S7 is built on the success of the UltiMaker S5 and its design decisions were heavily based on feedback from customers.
         
         
        So what’s new?
        The obvious change is the S7’s height. It now includes an integrated Air Manager. This filters the exhaust air of every print and also improves build temperature stability. To further enclose the build chamber the S7 only has one magnetically latched door.
         
        The build stack has also been completely redesigned. A PEI-coated flexible steel build plate makes a big difference to productivity. Not only do you not need tools to pop a printed part off. But we also don’t recommend using or adhesion structures for UltiMaker materials (except PC, because...it’s PC). Along with that, 4 pins and 25 magnets make it easy to replace the flex plate perfectly – even with one hand.
         
        The re-engineered print head has an inductive sensor which reduces noise when probing the build plate. This effectively makes it much harder to not achieve a perfect first layer, improving overall print success. We also reversed the front fan direction (fewer plastic hairs, less maintenance), made the print core door magnets stronger, and add a sensor that helps avoid flooding.
         

         
        The UltiMaker S7 also includes quality of life improvements:
        Reliable bed tilt compensation (no more thumbscrews) 2.4 and 5 GHz Wi-Fi A 1080p camera (mounted higher for a better view) Compatibility with 280+ Marketplace materials Compatibility with S5 project files (no reslicing needed) And a whole lot more  
        Curious to see the S7 in action?
        We’re hosting a free tech demo on February 7.
        It will be live and you can ask any questions to our CTO, Miguel Calvo.
        Register here for the Webinar
          • Like
        • 11 replies
        MariMakes

        Picked By

        MariMakes,
      • UltiMaker Cura 5.3.0-Alpha 🎄 Tree Support Spotlight 🎄

        Cura 5.3 Alpha With New Tree Support 🎄

        MariMakes posted a topic in Ultimaker Cura,

        Are you a fan of tree support, but dislike the removal process and the amount of filament it uses? Then we would like to invite you to try this special release of UltiMaker Cura. Brought to you by our special community contributor @thomasrahm
         
        We generated a special version of Cura 5.2 called 5.3.0 Alpha + Xmas. The only changes we introduced compared to UltiMaker Cura 5.2.1 are those which are needed for the new supports. So keep in mind, this is not a sneak peek for Cura 5.3 (there are some really cool new features coming up) but a spotlight release highlighting this new version of tree supports.  
          • Like
        • 17 replies
        MariMakes

        Picked By

        MariMakes,
      • New here? Get ahead with a free onboarding course

        New here? Get ahead with a free onboarding course

        SandervG posted a topic in Official news,

        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 14 replies
        SandervG

        Picked By

        SandervG,
      View All
    ×
    ×
    • Create New...