Jump to content

Cura 4.11.0 pauses print at height, but cannot resume after filament change

datamystic

By datamystic
in UltiMaker Cura

 Share

Recommended Posts

datamystic

datamystic 0

Posted
Posted (edited) · Cura 4.11.0 pauses print at height, but cannot resume after filament change

I’m trying to print one side of a borg cube (https://www.thingiverse.com/thing:4552821) and trying to change filament from translucent to black mid-print.

 

(I am using SnapMaker A150. I have reported the same issue in SnapMaker forums because it could be from gcode generation or gcode execution). https://forum.snapmaker.com/t/a150-pauses-print-at-height-but-cannot-resume-after-filament-change/21061

 

As Luban does not have the option to pause, I used Cura to add a pause at height of 1.4mm.

 

The Android SnapFab app crashed trying to parse the gcode first time around. I upgraded Luban to latest 4.0.3 and Cura to latest 4.11.0 last night, and this fixed the parsing issue.

 

Printing has strangely just paused (at 1.4mm), but the A150 screen must think it is printing, because it shows Pause/Stop buttons.

 

Also, I use Cura on my larger monitor. But the drop-down menus appear on my laptop monitor!

 

 

S2A_Borg_cube_sides - 218.3 scale.zip S2A_Borg_cube_sides - 218.3 scale.3mf

Edited by datamystic
    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...