Jump to content

Strange behaviour of Cura 4.13.1 (and also older versions)


Brumil

Recommended Posts

Posted · Strange behaviour of Cura 4.13.1 (and also older versions)

Hello

First, my system data:
Printer: AnyCubic Mega S Serie 1, Marlin 2.0
Octoprint with RaspI3b
Slicer: Cura 4.13.1

 

I have the following behavior on my system:

- I drew a cuboid (edge length 35mm, height 15mm) and exported it as STL

- loaded into Cura and sliced with the following settings: wall: 1, top:0, bottom 2, infill:0%, so the result is a shell without a lid, with wall thickness 1 (nozzle is 0.6mm), all speeds are at 100mm /s (don't worry, I don't really want to print with this).

- Printed (at a speed of 60mm), base plate starts like crazy, from layer 2 the printer falls asleep.

- Looked at G-code in text editor and found the following code:

;LAYER:10 ; Only an example, is for all layers >3
M205 X8 Y8
;TYPE:WALL-OUTER
;MESHConfusedingle_wall_box.stl
G1 F778.2 X117.492 Y127.2 E316.62785 ; print speed should be 6000!?
G1 X92.466 Y127.199 E317.8764
G1 X91.896 Y127.161 E317.9049
(...)

G1 F1535.1 X117.474 Y126.6 E366.66341; 2 walls 25,6mm/s
G1 F2268.6 X117.435 Y126 E377.49149 ; 3 walls 37,81 mm/s
G1 F2982.2 X92.549 Y125.399 E389.27574; 4 walls 49,7 mm/s
G1 F6000 X93.2 Y121.8 E1161.66962 ; 10 walls 100mm/s

Slicing again with one wall, but increasing the infill


G1 F2114.9 X117.492 Y127.2 E391.85053 ; 10% Infill
G1 F3323.2 X117.491 Y127.2 E443.19031 ; 20% Infill
G1 F4676.3 X117.491 Y127.2 E474.05769 ; 30% Infill
G1 F5779.3 X117.491 Y127.2 E486.18709 ; 40% Infill
G1 F6000 X117.491 Y127.2 E533.95532 ; ab 50% infill

Same thing, with "vase" mode:


;LAYER:10
;TYPE:WALL-OUTER
;MESHConfusedingle_wall_box.stl
G1 F777 X89.088 Y94.269 Z2.201 E322.83159
G1 X89.525 Y93.861 Z2.202 E322.86142
G1 X90.011 Y93.515 Z2.203 E322.89118

What happens here? I tried to print it at constant 100mm/s but I failed... Expecting all FXXX to be F6000. Any ideas?
 

curasettings.jpg

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...