Jump to content

Zahnrad gefunden

speedy110

By speedy110
in Deutsch

 Share
Go to solution Solved by speedy110,

Recommended Posts

speedy110

speedy110 0

Posted
Posted · Zahnrad gefunden

Beim saubermachen und etwas umkippen ist ein Zahnrad rausgefallen. Ich kann aber schnell normal drucken, bis auf das Problem das einige haben, das beim Drucken des Druckers zurückläuft. Das Zahnrad hat einen Durchmesser von 10 mm.

 

image.thumb.jpeg.14aea3a1400da195b9e3922688455d41.jpeg

 

    • Link to post
    Share on other sites
    zerspaner_gerd

    zerspaner_gerd 383

    Posted
    Posted · Zahnrad gefunden

    Das Zahnrad schaut mir danach aus das es selbst ausgedruckt wurde!!

     

    Glaub nicht das es einen Hersteller gibt der selbst gedruckte Zahnräder verwendet, da es einfach solche Mechanischen Teile stark belastet werden.

     

    Also meine Vermutung das dies einfach mit diesen Drucker ausgedruckt wurde

     

    Des weiteren wissen wir ja nicht Mal welchen Drucker du besitzt

     

    Gruß

    • Link to post
    Share on other sites
    ManAtArms

    ManAtArms 59

    Posted
    Posted (edited) · Zahnrad gefunden

    Kann mich meinem Vorredner nur anschließen, kein Hersteller verwendet 3D gedruckte Zahnräder in der "Qualität".

     

    Eventuell mal ausgedruckt und dann vergessen bzw. irgendwohin verschwunden und zufällig wieder aufgetaucht.

    Edited by ManAtArms
    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 3
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 26 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...