Jump to content

Trying to retrieve setting with no value given: prime_tower_mode Using CuraEngine on Mac


FelipeCC

Recommended Posts

Posted (edited) · Trying to retrieve setting with no value given: prime_tower_mode Using CuraEngine on Mac

Im trying to use CuraEngine to automate the slicing proccess on a Mac M1, i installed everything but i cant make it work yet

So the command i run is this

/Users/admin/CuraEngine/build/Release/CuraEngine slice -v -j /Users/admin/Desktop/Printer/creality_ender3.def.json -l /Users/admin/Desktop/Printer/ok.stl -o /Users/admin/Desktop/test.gcode -s extruder_nr=0

Gives me the error: Trying to retrieve setting with no value given: prime_tower_mode

im using cura definitions all def.json were retrieved from Cura's app folder

i have creality_ender3_def.json

creality_base.def.json

fdmprinter.def.json 

on the same folder

 

i tried adding -s prime_tower_mode=none, None, 0 ,1, single and nothing worked

Could it be that maybe im using a newer version of Cura to export the profile?

 

this is the entire settings print that curaengine makes on the terminal

 

[2024-04-12 21:05:43.470] [info] Loaded from disk in 0.054332584s

 

[2024-04-12 21:05:43.470] [info] All settings:  -s mesh_position_y="0.000000" -s center_object="false" -s group_outer_walls="true" -s raft_base_wall_count="1.000000" -s raft_remove_inside_corners="false" -s small_feature_speed_factor_0="50.000000" -s wipe_hop_speed="10.000000" -s wipe_pause="0.000000" -s wipe_retraction_prime_speed="2.000000" -s wipe_retraction_extra_prime_amount="0.000000" -s wipe_retraction_enable="true" -s clean_between_layers="false" -s bridge_skin_density_3="80.000000" -s bridge_skin_density_2="75.000000" -s bridge_skin_material_flow_2="100.000000" -s bridge_skin_speed_2="25.000000" -s bridge_enable_more_layers="true" -s bridge_skin_density="100.000000" -s bridge_skin_material_flow="60.000000" -s bridge_wall_material_flow="50.000000" -s bridge_wall_coast="100.000000" -s bridge_sparse_infill_max_density="0.000000" -s bridge_skin_support_threshold="50.000000" -s bridge_settings_enabled="false" -s adaptive_layer_height_threshold="0.200000" -s bridge_skin_speed_3="15.000000" -s magic_fuzzy_skin_point_dist="0.800000" -s magic_fuzzy_skin_enabled="false" -s support_conical_min_width="5.000000" -s support_conical_angle="30.000000" -s coasting_speed="90.000000" -s coasting_min_volume="0.800000" -s coasting_enable="false" -s conical_overhang_enabled="false" -s draft_shield_height_limitation="full" -s draft_shield_dist="10.000000" -s draft_shield_enabled="false" -s support_zag_skip_count="5.000000" -s support_skip_some_zags="false" -s interlocking_depth="2.000000" -s interlocking_beam_layer_count="2.000000" -s interlocking_orientation="22.500000" -s minimum_polygon_circumference="1.000000" -s material_flow_temp_graph="[[3.5, 200],[7.0, 240]]" -s infill_enable_travel_optimization="false" -s slicing_tolerance="middle" -s smooth_spiralized_contours="true" -s magic_spiralize="false" -s magic_mesh_surface_mode="normal" -s anti_overhang_mesh="false" -s mold_angle="40.000000" -s mold_roof_height="0.500000" -s mold_width="5.000000" -s mold_enabled="false" -s infill_mesh_order="0.000000" -s print_sequence="all_at_once" -s meshfix_fluid_motion_angle="15.000000" -s meshfix_fluid_motion_small_distance="0.010000" -s meshfix_maximum_deviation="0.025000" -s wipe_repeat_count="5.000000" -s meshfix_maximum_resolution="0.500000" -s alternate_carve_order="true" -s wipe_retraction_retract_speed="3.000000" -s multiple_mesh_overlap="0.150000" -s magic_fuzzy_skin_thickness="0.300000" -s meshfix_extensive_stitching="false" -s meshfix_union_all_remove_holes="false" -s meshfix_union_all="true" -s switch_extruder_extra_prime_amount="0.000000" -s ooze_shield_dist="2.000000" -s prime_tower_brim_enable="false" -s prime_tower_wipe_enabled="true" -s mesh_position_x="0.000000" -s prime_tower_position_y="200.000000" -s bridge_wall_min_length="5.000000" -s prime_tower_position_x="200.000000" -s prime_tower_min_volume="6.000000" -s prime_tower_size="20.000000" -s prime_tower_enable="false" -s raft_base_fan_speed="0.000000" -s raft_interface_fan_speed="0.000000" -s raft_surface_fan_speed="0.000000" -s raft_base_jerk="20.000000" -s raft_interface_jerk="20.000000" -s adaptive_layer_height_variation_step="0.010000" -s raft_surface_jerk="20.000000" -s raft_base_acceleration="3000.000000" -s raft_interface_acceleration="3000.000000" -s raft_surface_acceleration="3000.000000" -s raft_base_line_width="0.800000" -s machine_nozzle_heat_up_speed="2.000000" -s material_flush_purge_length="60.000000" -s raft_interface_line_spacing="0.900000" -s raft_interface_thickness="0.150000" -s lightning_infill_straightening_angle="40.000000" -s speed_topbottom="30.000000" -s raft_smoothing="5.000000" -s brim_inside_margin="2.500000" -s brim_replaces_support="true" -s acceleration_support_infill="3000.000000" -s brim_gap="0.000000" -s raft_surface_layers="2.000000" -s skirt_brim_minimal_length="250.000000" -s small_feature_speed_factor="50.000000" -s raft_interface_extruder_nr="0" -s skirt_brim_extruder_nr="-1" -s extruder_prime_pos_y="0.000000" -s support_mesh_drop_down="true" -s extruder_prime_pos_z="0.000000" -s support_tower_roof_angle="65.000000" -s support_tower_diameter="3.000000" -s support_use_towers="true" -s minimum_roof_area="1.000000" -s support_bottom_line_distance="0.400000" -s support_interface_skip_height="0.200000" -s support_bottom_enable="false" -s minimum_support_area="0.000000" -s support_roof_height="1.000000" -s material_bed_temperature_layer_0="60.000000" -s support_infill_sparse_thickness="0.100000" -s support_offset="0.800000" -s wipe_hop_amount="1.000000" -s meshfix_fluid_motion_shift_distance="0.100000" -s support_join_distance="2.000000" -s support_bottom_stair_step_min_slope="10.000000" -s prime_tower_raft_base_line_spacing="1.600000" -s support_bottom_stair_step_width="5.000000" -s support_xy_distance_overhang="0.200000" -s machine_nozzle_tip_outer_diameter="1.000000" -s min_infill_area="0.000000" -s support_xy_overrides_z="z_overrides_xy" -s support_xy_distance="0.700000" -s support_brim_enable="true" -s small_skin_width="1.000000" -s support_infill_angles="[ ]" -s prime_blob_enable="false" -s support_tree_tip_diameter="0.400000" -s cross_infill_pocket_size="2.000000" -s interlocking_enable="false" -s wall_line_width_0="0.400000" -s support_tree_top_rate="15.000000" -s switch_extruder_retraction_speed="20.000000" -s acceleration_roofing="3000.000000" -s retraction_hop_enabled="false" -s raft_surface_extruder_nr="0" -s interlocking_beam_width="0.800000" -s support_tree_branch_diameter_angle="7.000000" -s cool_fan_speed_0="0.000000" -s infill_support_enabled="false" -s support_brim_line_count="3.000000" -s bridge_fan_speed="100.000000" -s support_material_flow="100.000000" -s support_tree_max_diameter="25.000000" -s machine_steps_per_mm_y="50.000000" -s support_tree_branch_diameter="5.000000" -s machine_max_jerk_z="0.400000" -s support_tree_angle="60.000000" -s support_structure="normal" -s support_tree_limit_branch_reach="true" -s meshfix_maximum_travel_resolution="1.000000" -s support_extruder_nr_layer_0="0" -s support_enable="false" -s cool_min_layer_time="5.000000" -s cool_min_layer_time_fan_speed_max="10.000000" -s wall_overhang_angle="90.000000" -s cool_fan_enabled="true" -s cool_fan_speed_max="100.000000" -s wipe_move_distance="20.000000" -s cool_fan_speed_min="100.000000" -s support_bottom_extruder_nr="0" -s jerk_wall_0="20.000000" -s retraction_hop="1.000000" -s material_print_temp_wait="true" -s support_roof_angles="[ ]" -s build_volume_temperature="0.000000" -s extruder_prime_pos_x="0.000000" -s layer_start_y="0.000000" -s support_bottom_wall_count="0.000000" -s machine_min_cool_heat_time_window="50.000000" -s layer_start_x="0.000000" -s acceleration_infill="3000.000000" -s travel_avoid_supports="false" -s raft_surface_speed="20.000000" -s prime_tower_base_size="resolveOrValue('brim_width')" -s machine_height="250.000000" -s travel_retract_before_outer_wall="false" -s draft_shield_height="10.000000" -s machine_always_write_active_tool="false" -s z_seam_x="100.000000" -s retraction_combing_max_distance="0.000000" -s support_fan_enable="false" -s retraction_extrusion_window="4.500000" -s skirt_line_count="1.000000" -s retraction_count_max="90.000000" -s retraction_min_travel="1.500000" -s retraction_extra_prime_amount="0.000000" -s cool_min_speed="10.000000" -s z_seam_type="sharpest_corner" -s retraction_prime_speed="25.000000" -s retraction_amount="6.500000" -s support_line_distance="2.660000" -s retraction_enable="true" -s skin_edge_support_layers="4.000000" -s support_type="everywhere" -s jerk_travel_layer_0="20.000000" -s material_anti_ooze_retracted_position="-4.000000" -s hole_xy_offset="0.000000" -s jerk_print_layer_0="20.000000" -s jerk_travel="30.000000" -s travel_avoid_distance="0.625000" -s raft_interface_speed="15.000000" -s support_meshes_present="false" -s skin_outline_count="1.000000" -s jerk_prime_tower="20.000000" -s jerk_support_bottom="20.000000" -s jerk_roofing="20.000000" -s prime_tower_line_width="0.400000" -s jerk_wall_x_roofing="20.000000" -s jerk_wall_x="20.000000" -s jerk_infill="20.000000" -s jerk_enabled="false" -s wipe_brush_pos_x="100.000000" -s machine_nozzle_id="unknown" -s speed_equalize_flow_width_factor="100.000000" -s acceleration_travel_layer_0="3000.000000" -s gradual_support_infill_steps="0.000000" -s raft_base_extruder_nr="0" -s ironing_enabled="false" -s support_bottom_material_flow="100.000000" -s acceleration_travel="5000.000000" -s material_alternate_walls="false" -s material_break_preparation_speed="2.000000" -s material_end_of_filament_purge_length="20.000000" -s acceleration_support_bottom="3000.000000" -s support_roof_offset="0.000000" -s acceleration_support_roof="3000.000000" -s acceleration_topbottom="3000.000000" -s acceleration_wall_x_roofing="3000.000000" -s jerk_wall_0_roofing="20.000000" -s flow_rate_extrusion_offset_factor="100.000000" -s carve_multiple_volumes="true" -s acceleration_wall_x="3000.000000" -s acceleration_travel_enabled="true" -s support_roof_extruder_nr="0" -s acceleration_enabled="false" -s speed_z_hop="10.000000" -s switch_extruder_retraction_amount="20.000000" -s machine_nozzle_temp_enabled="true" -s material_maximum_park_duration="300.000000" -s skirt_brim_speed="30.000000" -s speed_travel_layer_0="60.000000" -s material_bed_temperature="60.000000" -s support_tree_rest_preference="buildplate" -s support_infill_extruder_nr="0" -s speed_prime_tower="60.000000" -s support_bottom_angles="[ ]" -s support_tree_angle_slow="50.000000" -s speed_support_roof="40.000000" -s max_extrusion_before_wipe="10.000000" -s raft_base_line_spacing="1.600000" -s speed_support_infill="60.000000" -s speed_infill="60.000000" -s infill_extruder_nr="-1" -s support_roof_wall_count="0.000000" -s material_is_support_material="false" -s support_bottom_stair_step_height="0.300000" -s speed_roofing="25.000000" -s brim_outside_only="true" -s material_standby_temperature="150.000000" -s wall_0_material_flow_layer_0="100.000000" -s prime_tower_flow="100.000000" -s acceleration_ironing="3000.000000" -s roofing_material_flow="100.000000" -s machine_nozzle_size="0.400000" -s wall_x_material_flow_roofing="100.000000" -s ironing_only_highest_layer="false" -s jerk_support_roof="20.000000" -s machine_extruder_count="1.000000" -s wall_0_material_flow_roofing="100.000000" -s material_print_temperature_layer_0="215.000000" -s top_bottom_extruder_nr="-1" -s wipe_retraction_amount="1.000000" -s material_break_temperature="50.000000" -s infill_mesh="false" -s layer_height="0.100000" -s material_break_preparation_retracted_position="-16.000000" -s brim_smart_ordering="true" -s machine_head_with_fans_polygon="[[-26.000000,34.000000],[-26.000000,-32.000000],[32.000000,-32.000000],[32.000000,34.000000]]" -s z_seam_corner="z_seam_corner_inner" -s support_conical_enabled="false" -s material_anti_ooze_retraction_speed="5.000000" -s support_bottom_distance="0.100000" -s machine_steps_per_mm_e="1600.000000" -s material_crystallinity="false" -s material_guid="" -s material_shrinkage_percentage_z="100.000000" -s interlocking_boundary_avoidance="2.000000" -s min_even_wall_line_width="0.300000" -s material_print_temperature="210.000000" -s material_shrinkage_percentage_xy="100.000000" -s speed_support_bottom="40.000000" -s acceleration_wall_0_roofing="3000.000000" -s material_extrusion_cool_down_speed="0.700000" -s ooze_shield_angle="60.000000" -s machine_endstop_positive_direction_x="false" -s material_final_print_temperature="195.000000" -s material_break_retracted_position="-50.000000" -s material_initial_print_temperature="200.000000" -s jerk_skirt_brim="20.000000" -s machine_heat_zone_length="16.000000" -s speed_slowdown_layers="2.000000" -s default_material_print_temperature="210.000000" -s raft_surface_line_spacing="0.400000" -s material_no_load_move_factor="0.940860" -s infill_support_angle="40.000000" -s material_bed_temp_prepend="true" -s infill_before_walls="true" -s wall_distribution_count="1.000000" -s raft_airgap="0.300000" -s material_flush_purge_speed="0.500000" -s machine_show_variants="false" -s gradual_infill_steps="0.000000" -s mesh_position_z="0.000000" -s conical_overhang_angle="50.000000" -s infill_overlap_mm="0.040000" -s adhesion_type="brim" -s infill_angles="[ ]" -s retraction_retract_speed="25.000000" -s zig_zaggify_infill="false" -s speed_print_layer_0="30.000000" -s wall_x_material_flow_layer_0="100.000000" -s top_skin_expand_distance="1.000000" -s speed_wall_0_roofing="30.000000" -s sub_div_rad_add="0.400000" -s bottom_skin_preshrink="1.000000" -s default_material_bed_temperature="60.000000" -s machine_max_acceleration_e="10000.000000" -s speed_ironing="20.000000" -s bridge_fan_speed_3="0.000000" -s ironing_inset="0.350000" -s ironing_flow="10.000000" -s min_skin_width_for_expansion="0.000000" -s wall_x_material_flow="100.000000" -s infill_material_flow="100.000000" -s ironing_monotonic="false" -s layer_0_z_overlap="0.220000" -s speed_travel="120.000000" -s ironing_pattern="zigzag" -s lightning_infill_prune_angle="40.000000" -s raft_surface_line_width="0.400000" -s skin_no_small_gaps_heuristic="false" -s small_skin_on_surface="false" -s raft_interface_line_width="0.700000" -s infill_offset_x="0.000000" -s gantry_height="99999999999.000000" -s material_surface_energy="100.000000" -s acceleration_wall_0="3000.000000" -s adaptive_layer_height_variation="0.100000" -s cross_infill_density_image="" -s raft_interface_layers="1.000000" -s bridge_skin_speed="15.000000" -s skirt_brim_material_flow="100.000000" -s wall_transition_filter_deviation="0.100000" -s material_break_preparation_temperature="50.000000" -s meshfix_fluid_motion_enabled="true" -s infill_pattern="grid" -s connect_skin_polygons="false" -s alternate_extra_perimeter="false" -s support_roof_enable="false" -s skin_material_flow_layer_0="100.000000" -s top_bottom_pattern_0="lines" -s roofing_pattern="lines" -s meshfix_maximum_extrusion_area_deviation="50000.000000" -s wall_0_material_flow="100.000000" -s raft_base_thickness="0.300000" -s retraction_hop_after_extruder_switch="true" -s support_top_distance="0.100000" -s wall_line_width_x="0.400000" -s roofing_extruder_nr="-1" -s raft_margin="15.000000" -s machine_max_jerk_e="5.000000" -s small_feature_max_length="0.000000" -s skin_overlap_mm="0.020000" -s machine_name="Creality Ender-3" -s hole_xy_offset_max_diameter="0.000000" -s adaptive_layer_height_enabled="false" -s support_connect_zigzags="true" -s xy_offset_layer_0="0.000000" -s support_interface_priority="interface_area_overwrite_support_area" -s xy_offset="0.000000" -s support_mesh="false" -s support_roof_pattern="concentric" -s inset_direction="inside_out" -s switch_extruder_prime_speed="20.000000" -s wall_x_extruder_nr="-1" -s min_bead_width="0.200000" -s machine_minimum_feedrate="0.000000" -s optimize_wall_printing_order="false" -s infill_multiplier="1.000000" -s initial_layer_line_width_factor="100.000000" -s machine_start_gcode="; Ender 3 Custom Start G-code

G92 E0 ; Reset Extruder

G28 ; Home all axes

G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed

G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position

G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line

G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little

G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line

G92 E0 ; Reset Extruder

G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed

G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish" -s relative_extrusion="false" -s wall_0_inset="0.000000" -s wall_0_wipe_dist="0.200000" -s support_tree_max_diameter_increase_by_merges_when_support_to_model="1.000000" -s material_print_temp_prepend="true" -s machine_max_feedrate_z="299792458000.000000" -s wall_line_count="2.000000" -s infill_line_distance="2.000000" -s minimum_bottom_area="1.000000" -s wall_0_extruder_nr="-1" -s remove_empty_first_layers="true" -s jerk_topbottom="20.000000" -s wall_transition_filter_distance="100.000000" -s support_supported_skin_fan_speed="100.000000" -s infill_wall_line_count="0.000000" -s ooze_shield_enabled="false" -s support_line_width="0.400000" -s support_initial_layer_line_distance="2.660000" -s machine_firmware_retract="false" -s layer_height_0="0.300000" -s travel_avoid_other_parts="true" -s acceleration_print_layer_0="3000.000000" -s machine_end_gcode="G91 ;Relative positioning

G1 E-2 F2700 ;Retract a bit

G1 E-2 Z0.2 F2400 ;Retract and raise Z

G1 X5 Y5 F3000 ;Wipe out

G1 Z10 ;Raise Z more

G90 ;Absolute positioning

 

G1 X0 Y{machine_depth} ;Present print

M106 S0 ;Turn-off fan

M104 S0 ;Turn-off hotend

M140 S0 ;Turn-off bed

 

M84 X Y E ;Disable all steppers but Z

" -s machine_center_is_zero="false" -s extruders_enabled_count="1.000000" -s machine_endstop_positive_direction_y="false" -s retraction_hop_only_when_collides="false" -s machine_feeder_wheel_diameter="10.000000" -s magic_fuzzy_skin_outside_only="false" -s support_tree_bp_diameter="7.500000" -s infill_line_width="0.400000" -s roofing_line_width="0.400000" -s retract_at_layer_change="false" -s wall_transition_length="0.400000" -s support_bottom_line_width="0.400000" -s machine_steps_per_mm_x="50.000000" -s machine_nozzle_head_distance="3.000000" -s machine_width="235.000000" -s machine_max_feedrate_x="299792458000.000000" -s infill_randomize_start_location="false" -s top_layers="8.000000" -s speed_wall_x="60.000000" -s machine_buildplate_type="glass" -s skin_angles="[ ]" -s machine_steps_per_mm_z="50.000000" -s nozzle_disallowed_areas="[]" -s support_tower_maximum_supported_diameter="3.000000" -s conical_overhang_hole_size="0.000000" -s jerk_travel_enabled="true" -s prime_tower_base_curve_magnitude="4.000000" -s material_adhesion_tendency="10.000000" -s machine_extruders_shared_nozzle_initial_retraction="0.000000" -s extruder_prime_pos_abs="false" -s cutting_mesh="false" -s machine_max_jerk_xy="20.000000" -s machine_acceleration="4000.000000" -s jerk_ironing="20.000000" -s roofing_angles="[ ]" -s prime_tower_base_height="0.000000" -s fill_outline_gaps="true" -s cool_fan_full_layer="2.000000" -s top_bottom_pattern="lines" -s skirt_brim_line_width="0.400000" -s gradual_support_infill_step_height="1.000000" -s mesh_rotation_matrix="[[1,0,0], [0,1,0], [0,0,1]]" -s support_wall_count="1.000000" -s machine_max_acceleration_z="100.000000" -s support_tree_min_height_to_model="3.000000" -s acceleration_skirt_brim="3000.000000" -s meshfix_keep_open_polygons="false" -s skin_monotonic="false" -s machine_max_acceleration_y="9000.000000" -s bottom_skin_expand_distance="1.000000" -s z_seam_y="100.000000" -s machine_max_acceleration_x="9000.000000" -s bottom_layers="6.000000" -s infill_offset_y="0.000000" -s brim_line_count="20.000000" -s support_roof_line_distance="0.400000" -s machine_max_feedrate_e="299792458000.000000" -s machine_nozzle_expansion_angle="45.000000" -s min_odd_wall_line_width="0.300000" -s lightning_infill_overhang_angle="40.000000" -s machine_shape="rectangular" -s machine_heated_bed="true" -s machine_use_extruder_offset_to_offset_coords="true" -s support_tree_branch_reach_limit="30.000000" -s skin_material_flow="100.000000" -s min_feature_size="0.100000" -s bridge_wall_speed="15.000000" -s support_bottom_offset="0.000000" -s raft_surface_thickness="0.100000" -s support_roof_material_flow="100.000000" -s machine_max_feedrate_y="299792458000.000000" -s retraction_combing="all" -s material_flow_layer_0="100.000000" -s flow_rate_max_extrusion_offset="0.000000" -s material_diameter="1.750000" -s wall_overhang_speed_factor="100.000000" -s jerk_support_infill="20.000000" -s speed_wall_0="30.000000" -s cool_lift_head="false" -s machine_extruders_share_heater="false" -s top_skin_preshrink="1.000000" -s skirt_height="3.000000" -s connect_infill_polygons="true" -s skin_line_width="0.400000" -s support_bottom_pattern="concentric" -s support_pattern="zigzag" -s coasting_volume="0.064000" -s machine_endstop_positive_direction_z="true" -s speed_wall_x_roofing="60.000000" -s infill_wipe_dist="0.040000" -s wipe_hop_enable="true" -s zig_zaggify_support="false" -s machine_depth="235.000000" -s material_bed_temp_wait="true" -s material_break_speed="25.000000" -s cross_support_density_image="" -s z_seam_relative="false" -s skirt_gap="3.000000" -s retraction_hop_after_extruder_switch_height="1.000000" -s acceleration_prime_tower="3000.000000" -s support_roof_line_width="0.400000" -s machine_nozzle_cool_down_speed="2.000000" -s infill_sparse_thickness="0.100000" -s ironing_line_spacing="0.100000" -s machine_disallowed_areas="[[[-117.500000,117.500000],[-117.500000,108.000000],[117.500000,108.000000],[117.500000,117.500000]],[[-117.500000,-108.000000],[-117.500000,-117.500000],[117.500000,-117.500000],[117.500000,-108.000000]]]" -s support_bottom_height="1.000000" -s machine_extruders_share_nozzle="false" -s machine_heated_build_volume="false" -s gradual_infill_step_height="1.500000" -s wall_transition_angle="10.000000" -s raft_base_speed="15.000000" -s support_angle="50.000000" -s machine_gcode_flavor="RepRap (Marlin/Sprinter)" -s material_end_of_filament_purge_speed="0.500000" -s machine_scale_fan_speed_zero_to_one="false" -s bridge_skin_material_flow_3="110.000000" -s bridge_fan_speed_2="0.000000" -s initial_bottom_layers="6.000000" -e0 -g -e1 -l "0" -s extruder_nr="1"

 

[2024-04-12 21:05:43.471] [error] Trying to retrieve setting with no value given: prime_tower_mode

Edited by FelipeCC
  • Link to post
    Share on other sites

    Posted · Trying to retrieve setting with no value given: prime_tower_mode Using CuraEngine on Mac

    You are way beyond me but it is a new setting in 5.7.0.  It can be "normal" or "interleaved" so it is a string.

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...