Jump to content

"polar wind" air cooling system for the Ultimaker 2

ksn-arts
 Share

Recommended Posts

ksn-arts

ksn-arts 84

Posted
Posted · "polar wind" air cooling system for the Ultimaker 2

Hi all ....in my room sometimes very warm above 30 degrees Celsius. I noticed that at the bottom, where there is a micro computer board printer, too much heat at the bottom. and little air movement. within two days, I developed a system of heat blowing from under the printer. this device I called the "polar wind". it works on the fan from USB. and is designed for installation at the bottom of the printer. blowing hot air into the side of the board micro computer. air cooling system for the printer.tomorrow I will start printing 3d...

Pw4

Pw3

Pw2

Pw1

3d modeling idea and development Sergey Kolesnik

 

    • Link to post
    Share on other sites
    ksn-arts

    ksn-arts 84

    Posted
    • Author
    Posted · "polar wind" air cooling system for the Ultimaker 2

    3hd

    2hd

    1hd

    hot air extractor is connected and running. beautiful lighting. system is powered separately from the electricity charge your cell phone samsung.

    Cl

     

    • Link to post
    Share on other sites
    DidierKlein

    DidierKlein 729

    Posted
    Posted · "polar wind" air cooling system for the Ultimaker 2

    Nice work :) Pimp my UM2

    It's a good idea to cool down the electronics :)

     

    • Link to post
    Share on other sites
    ksn-arts

    ksn-arts 84

    Posted
    • Author
    Posted · "polar wind" air cooling system for the Ultimaker 2

    Nice work :) Pimp my UM2

    It's a good idea to cool down the electronics :)

     

    Thanks I'll post later 3d model for download.:)

     

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 0
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...