Jump to content

Defekter Ulticontroller oder Fehler auf der Hauptplatine?


Recommended Posts

Posted · Defekter Ulticontroller oder Fehler auf der Hauptplatine?

Hi,

hier erstmal eine Zusammenfassung meiner Odyssee mit meinem geliebten Ultimaker.

- Umbau auf dual extrusion; beim einschalten kam nur noch ein grelles piepen aus dem ulticontroller

- alle Kabel und stecke geprüft könnte keinen Fehler meiner Seite entdecken.

- arduino Board wird seit dem nicht mehr vom pc erkannt; Orange led leuchtet oder blinkt nicht mehr < wohl defekt

- neues arduino Board besorgt, Firmware aufgespielt, zusammengebaut; Ergebnis: Stepper Module werden heiß, ulticontroller zeigt nur Vierecke, ein motor ist am zucken und arduino startet nach kurzer Zeit permanent neu, nur das piepen vom ulticontroller ist weg. < Board defekt?

- da ich Geld sparen muss, dann dieses board besorgt, https://www.amazon.de/dp/B00H9917FC/ref=cm_sw_r_awd_p4HMub1TRJJCX

gleich mit neuen Stepper Modulen bestellt. Zusammengebaut widerstände für die beiden thermosensensoren rausgelöstet, Stecker angepasst und nun läuft er so weit wieder, nur der ulticontroller zeigt nach wie vor die viereckigen Kästchen an und piept auch nicht.

Und das ist nun auch mein Problem, ich bekomme den ulticontroller nicht zum laufen. Das einzige was mir aufgefallen ist, auf dem neuen Nachbau board fehlt ein Bauteil, nämlich das kleine blaue neben den Anschlüssen für den ulticontroller, (C7 steht an dem Anschluss) dieser fehlt auf dem neuen Nachbau board.

Was ist das für ein Teil und ist der für den ulticontroller notwendig?!

Danke schonmal für eine Antwort/Ideen und allen ein frohes Weihnachtsfest.

  • Link to post
    Share on other sites

    Posted · Defekter Ulticontroller oder Fehler auf der Hauptplatine?

    Hi nochmals,

    No Risk no fun, ich habe das Bauteil aus dem alten Board rausgelötet und im Nachbau Board eingelötet, und keine Veränderung.

    Da ich noch nen alten Controller, zwar mit defekter Beleuchtung habe, habe ich diesen mal angeklemmt und er zeigt mir wieder alles an, nur halt ohne Beleuchtung.

    D.h. Mein Ultimaker hat irgendwo nen heftigen Kurzschluss gehabt und mir mein arduino, Ultimaker board und den Ulticontroller zerschossen.

    Ich weiß nur nicht wie und wo das passiert ist, echt ärgerlich.

    Naja, lieben Gruß und schöne Feiertage.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Help Us Improve Cura – Join the Ultimaker Research Program
        🚀 Help Shape the Future of Cura and Digital Factory – Join Our Power User Research Program!
        We’re looking for active users of Cura and Digital Factory — across professional and educational use cases — to help us improve the next generation of our tools.
        Our Power User Research Program kicks off with a quick 15-minute interview to learn about your setup and workflows. If selected, you’ll be invited into a small group of users who get early access to features and help us shape the future of 3D printing software.

        🧪 What to Expect:
        A short 15-minute kickoff interview to help us get to know you If selected, bi-monthly research sessions (15–30 minutes) where we’ll test features, review workflows, or gather feedback Occasional invites to try out early prototypes or vote on upcoming improvements
        🎁 What You’ll Get:
         
        Selected participants receive a free 1-year Studio or Classroom license Early access to new features and tools A direct voice in what we build next
        👉 Interested? Please fill out this quick form
        Your feedback helps us make Cura Cloud more powerful, more intuitive, and more aligned with how you actually print and manage your workflow.
        Thanks for being part of the community,

        — The Ultimaker Software Team
        • 0 replies
      • Cura 5.10 stable released!
        The full stable release of Cura 5.10 has arrived, and it brings support for the new Ultimaker S8, as well as new materials and profiles for previously supported UltiMaker printers. Additionally, you can now control your models in Cura using a 3D SpaceMouse and more!
          • Like
        • 18 replies
    ×
    ×
    • Create New...