Jump to content

repead a print true doodle3d nozzle does not heatup again.


makerman

Recommended Posts

Posted · repead a print true doodle3d nozzle does not heatup again.

When printing true doodle3d and a second print is started the

nozzle stays cold.

This can be a Doodle3D Problem.

I have a UM0, two heads, heated bed, ultimaker controller.

Cura 15.02.1 and a Doodle3d box.

Cura detects the Doodle3D box.

After slicing I hit the top middle button it says print with

Doodle3D. After a popup window saying:

Printer found waiting for print command.

Temperature: 23 Bed: 19

And a print button.

After hitting the button I see the bet is going to 70 C

Nozzle still 23

The gcode is send to the Doodle3D box and the heated

bed starts to rise in temperature.

The temp is displayed in the ulticontroller and in the pop-up window.

After the bed has reached the set temperature the nozzle temp starts

rising. When it reached the set temp printing starts normally.

So far so good.

After printing the nozzle and bed cools down to room temp.

Cura shows the initial pop-up window with the print button.

After hitting the print button again the bed rises in temp.

Cura is sending the gcode again. After the bed set temp is

reached...

Nothing happens. Nozzle stays cool!

Then after a few minutes the printer starts, even when the

nozzle is still cold!!!

Pulling the USB between printer and Doodle3D and switching

the printer off. Closing cura.

Note:Doodle3D is still powered.

Starting cura, load model, slicing starts, hitting the cura

middle button, pop-up shows, hit print button, cura send gcode,

Bed heats up and then...

Nozzle stays cool!

This problem might be in Doodle3D.

Can someone confirm this.

Should I post this on the Doodle3D forum?

  • Link to post
    Share on other sites

    • 1 month later...

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
      • Ultimaker Cura 5.6 stable released
        Cura now supports Method series printers!
         
        A year after the merger of Ultimaker and MakerBotQQ, we have unlocked the ability for users of our Method series printers to slice files using UltiMaker Cura. As of this release, users can find profiles for our Method and Method XL printers, as well as material profiles for ABS-R, ABS-CF, and RapidRinse. Meaning it’s now possible to use either Cura or the existing cloud-slicing software CloudPrint when printing with these printers or materials
        • 48 replies
    ×
    ×
    • Create New...