bob-hepple
-
Posts
624 -
Joined
-
Last visited
-
Days Won
3
Content Type
Forums
Events
3D Prints
Posts posted by bob-hepple
-
-
All
ok I did a simple gcode file
M92 E492.45
M500
G28 ; Home all axes
G1 F3000 X20 Y20 Z20 ; Bring extruder to the front slowly
G28
ran it to printer how can I tell or not?? if the E steps worked is it print and see ???
-
Glad you got it sorted don't know why you had the problems, when you set the steps how did you do it. Just so I know, I'm going to upload tinkGnomes latest firmware and set steps/mm
-
Neotko
Thanks a bit bemused at moment why this has to be done given I downloaded a modded firmware.
But that is me and my learning curve is still developing, no doubt it will enlighten me.
Thank you
-
The Gcode is one file which you sort of tell the printer to print - it just changes the filament print rate and thats it, you just execute once and it writes the new parameter into the firmware of the UM2
the two lines are below:-
M92 E492.45
M500
you can just copy them to a file and give it a GCODE file type - job done
stu_le_brew
thanks for this I created gcode file with the two lines of code and printed it is that it...
Bob
-
eldrick
thanks for this while I have just finished installing I'm confused I asked Bondtech if I had to change the steppes millimetre page 11 in there Manual and I was under the impression that if I downloaded there firmware I didn't..
have you done anything like they suggested ???
please see my post to tinkerGnome
https://ultimaker.com/en/community/20164-filament-spacing-question-for-ultimaker-2?page=1#unread
-
tinkerGnome
love your firmware by the way...
I asked that specific Question to Bondtech and the answer I got back was download there firmware which is your moded ?? then no need for the Gcode, I have done a print out it seemed good
??????
-
done some calcs on your print speed they are a lot more than I am printing I am at 210 at 1800.0 /60 =30 you are at 50 also it depends on which Nozzle style you are using which nozzle ??
-
chuck
I don't use cura so my help is limited was it working before you fitted the Bondtech
-
Bondtech
Fitted you extruder and your firmware all is working ran a couple of files through to compare it worked I think my S3d setting need to be changed
1. my flow needs to be reduced for first layer because the Bondtech has more power first layer is now quiet full.
2 My retractions speed need to be adjusted set at 2500.0 mm/min do you have any suggestions for this one??
-
chuck
yes you are correct I have just fitted the Bondtech I use S3D and it is fine (ish) I was under the impression the Hex File was moded already from TinkerGnomes Firmware.
-
Larsgw
sorry to say it but you found the week link in the machine, I would tighten the tension hold your breath till the new extruder arrives, you will be less frustrated in the end. It is an issue and it is well documented. I had my machine for 2 years and it was documented then. I hear the new feeder is much better, I found to help with this problem is to increase the heat carefully and slower your print.
sorry to be a bit gloomy but your problems is what I have had for months.
Good Luck
-
bondtech
thanks for this at least there is options. I will let you know how I get on..
Neotko
Agree with your sentiments and I think I will experiment, when it arrives, which I am greatly looking forward to.
-
Gr5
I usually wait till the material is purged then I have a wire that I use to wrap said material and then pull it away..
mikehddd
have a look in the software forum under s3d I think my start up script is there if not I post it hear for you its not the best but it has served me well over the last 16 months.
-
Bondtech
will download your firmware when Parcel arrives, I have been playing with TinkerGnomes 16.01 Love it..
neotko
can't agree with you more, I thought the same it is actually a benefit for the motor to skip instead of pushing material through, I hope that this can be overcome, or i have just swapped a pain in the Axxx for a more serious problem. Don't like the idea of thread Lock, also the 3dSolex Steel Coupler thread has a lot more slop than the original UM Version, if the Steel coupler is tighter in the thread this might also make a differenced. Was going to Ask 3dSolex if this was or is possible I might just have a bad one.
-
1
-
-
ColorFabb for me to Don't like the White though
-
Hi
yes I use S3D along with others I Like it, I would urge caution when using your new machine based on my experience which was very bad. On Delivery a wire was Jammed under the Micro switch causing the head to crash into plate. Make sure they are All Clear of Obstructions.
Then Good to Go.
-
Erick407A
I also ordered the Bondtech I think it will be a Pleasant surprise. (?????)
-
1
-
-
Ok Ill take on board your comments and try a few calcs.
Thanks to all
-
Join the club,
-
1
-
-
Ultiarjan
Thanks for the reply using S3D would that make a difference.
-
Any idea how to get my print time more accurately counted on console ie. it says I have 1 min left to print but actually its more like 5.
using TinkerGnomes 16.01
-
installed 16.01 it is running my Gcode from Smf3D looks good
-
OK will download and install 16.01 Thanks
-
Thanks
are you using Cura OR Simplify 3D which I'm using I take it the Gcode goes into start script
Where can I find a list of part numbers
in UltiMaker 3D printers
Posted
Hi All
want to do a list of parts needed for the machine as it is now. And also the new updated 2+ printer head parts where do I find the part numbers