Jump to content
Ultimaker Community of 3D Printing Experts

Gambody_3D

Member
  • Content count

    24
  • Joined

  • Last visited

3D Print posted by Gambody_3D

  1. Atlas Titan Arm and Rifle

    This model was tested in Cura 2.3.1. To avoid printing problems, we recommend the following settings:
    Quality
    Layer Height: 0.1 mm
    Initial Layer Height: 0.3 mm
    Line Width: 0.4 mm
    Wall Line Width: 0.4 mm
    Outer Wall Line Width: 0.4 mm
    Inner Wall(s) Line Width: 0.4 mm
    Top/Bottom Line Width: 0.4 mm
    Infill Line Width: 0.4 mm
    Skirt/Brim Line Width: 0.4 mm
    Support Line Width: 0.4 mm
    Shell
    Wall Thickness: 0.8 mm
    Wall Line Count: 2
    Top/Bottom Thickness: 0.8 mm
    Top Thickness: 0.8 mm
    Top Layers: 8
    Bottom Thickness: 0.8 mm
    Bottom Layers: 8
    Top/Bottom Pattern: Lines
    Outer Wall Inset: 0 mm
    Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
    Horizontal Expansion: 0 mm
    Z Seam Alignment: Shortest
    Infill
    Infill Density: 25%
    Infill Line Distance: 3.2 mm
    Infill Pattern: Grid
    Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
    Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
    Infill Wipe Distance: 0.1 mm
    Infill Layer Thickness: 0.1 mm
    Gradual Infill Steps: 0
    Infill Before Walls: Check
    Material
    Enable Retraction: Check
    Retraction Extra Prime Amount: 0 mm3
    Retraction Minimum Travel: 0.8 mm
    Maximum Retraction Count: 90
    Minimum Extrusion Distance Window: 6.5 mm
    Standby Temperature: 175°C
    Nozzle Switch Retraction Distance: 16 mm
    Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s
    Speed
    Print Speed: 60 mm/s
    Infill Speed: 80 mm/s
    Wall Speed: 30 mm/s
    Outer Wall Speed: 30 mm/s
    Inner Wall Speed: 60 mm/s
    Top/Bottom Speed 15 mm/s
    Support Speed: 60 mm/s
    Support Infill Speed: 60 mm/s
    Travel Speed: 120 mm/s
    Initial Layer Speed: 15 mm/s
    Initial Layer Print Speed: 15 mm/s
    Initial Layer Travel Speed: 30 mm/s
    Skirt/Brim Speed 15 mm/s
    Maximum Z Speed: 0 mm/s
    Travel
    Combing Mode: All
    Avoid Printed Parts when Traveling: Check
    Travel Avoid Distance: 0.625 mm
    Cooling
    Enable Print Cooling: Check
    Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100%
    Regular/Maximum Fan Speed Threshold: 10 s
    Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2
    Minimum Layer Time: 5 s
    Minimum Speed: 10 mm/s
    Support
    Enable Support: Check
    Support Placement: Everywhere
    Support Overhang Angle: 50°
    Support Pattern: Zig Zag
    Connect Support ZigZags: Check
    Support Density: 30 %
    Support Line Distance: 1.3333 mm
    Support Z Distance: 0.1 mm
    Support Top Distance: 0.1 mm
    Support Bottom Distance: 0.1 mm
    Support X/Y Distance: 0.7 mm
    Support Distance Priority: Z overrides X/Y
    Minimum Support X/Y Distance: 0.2 mm
    Support Stair Step Height: 0.3 mm
    Support Join Distance: 2.0 mm
    Support Horizontal Expansion: 0.2 mm
    Use Towers: Check
    Tower Diameter: 3.0 mm
    Minimum Diameter: 3.0 mm
    Tower Roof Angle: 65°
    Build Plate Adhesion
    Build Plate Adhesion Type: Brim
    Skirt/Brim Minimum Length: 250 mm
    Brim Width: 8.0 mm
    Brim Line Count: 20
    Brim Only on Outside: Check
    Mesh Fixes
    Union Overlapping Volumes: Check
    Special Modes
    Print Sequence: All at Once
    Surface Mode: Normal
    Experimental
    Extra Skin Wall Count: 0

    847 downloads

       (0 reviews)

    0 comments

    Updated

  2. 3D Printed and Painted Terran Space Marine

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 30mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 1.5mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Lines
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    3,109 downloads

       (0 reviews)

    0 comments

    Updated

  3. Jesse McCree 3D model Printing Recommendations

    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.

    1,690 downloads

       (0 reviews)

    0 comments

    Updated

  4. Star Wars Boba Fett

    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.

    875 downloads

       (0 reviews)

    0 comments

    Updated

  5. Gipsy Danger 3D Model

    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 30mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 1.5mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.

    1,824 downloads

       (0 reviews)

    0 comments

    Updated

  6. Malcador Infernus

    Quality:
    Layer height - 0.1mm
    Initial layer thickness - 0.3mm
    Bottom/top pattern - lines
    Horizontal expansion - 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    Speed setups:
    Infill speed - 50mm/s
    Outer shell speed - 30mm/s
    Inner shell speed - 20mm/s
    Top/Bottom speed - 20mm/s
    Support speed - 50mm/s
    Travel speed - 150mm/s
    Skirt speed - 30mm/s
    Amount of slower layers - 4
    Infill:
    Infill Pattern - Grid
    Line distance - 3mm
    Infill Overlap - 20%
    Infill Layers - 0
    Support
    Enable Support - check
    Placement - Everywhere
    Overhang angle - 30°
    X/Y Distance - 0.7mm
    Top Distance - 0.2mm
    Bottom Distance - 0.2mm
    Stair Step Height - 0.5mm
    Join Distance - 0.7mm
    Area Smoothing - 0.6mm
    Use towers - check
    Pattern - Lines
    Line distance - 1.5mm
    Platform Adhesion
    Type - Brim
    Brim Line Count -12 (up to 20, depending on the model’s height)
    The model’s parts have been test printed in PLA
    Recommendations
    All parts will arrange on the print bed in such a way as to get a clean printing, all basic settings by default.

    1,302 downloads

       (0 reviews)

    0 comments

    Updated

  7. AT-AT Printing Recommendations

    Layer height: 0.1mm (for a clean result)*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Horizontal expansion 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed: 30mm/s
    Inner shell speed: 20mm/s
    Top/Bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30 mm/s
    Amount of slower layers: 4
    Infill:
    InfillpPattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers - 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2 mm
    Stair step height: 0.5 mm
    Join distance: 0.7 mm
    Area smoothing - 0.6 mm
    Use towers: Check. When removing secondary structure, the model remains clean.
    Pattern: Grid
    Line distance - 1.5mm (for higher detail fidelity and to avoid object deformation during printing)
    Platform Adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    All basic settings by default.
    Other recommendations: To make printing faster use layer height - 0.2mm for B1, B2, B3, B4, B5, B6, B8, B9, B10, B11, B12, B13, B14, B15, B16, B17, B23, B24, B25, leg parts, as they lack element detail. For other parts use 0.1mm to ensure high printing quality.
    Apply basic settings.

    1,506 downloads

       (0 reviews)

    0 comments

    Updated

  8. 3D printed Kratos

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm
    Speed setups for figure:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Speed setups for axes: It is recommended to print the axes at 0.1mm layer height.
    Infill speed: 50mm/s
    Outer shell speed: 20mm/s
    Inner shell speed: 20mm/s
    Top/Bottom speed: 20mm/s
    Support speed: 30mm/s
    Travel speed: 150mm/s
    Skirt speed: 20mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Lines
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)

    1,441 downloads

       (0 reviews)

    0 comments

    Updated

  9. Terran Space Marine 3D model

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 30mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 1.5mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Lines
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    1,475 downloads

       (0 reviews)

    0 comments

    Updated

  10. Kayle 3D Print Model

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation.  Apply other settings by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    4,157 downloads

       (0 reviews)

    2 comments

    Updated

  11. Tesla Power Armor 3D model Printing Details

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Lines
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    4,637 downloads

       (0 reviews)

    0 comments

    Updated

  12. Scorpion 3D Model from Mortal Kombat

    Quality
    Layer height: 0.1mm
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed: 30mm/s
    Inner shell speed; 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 100mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: Check
    Pattern: Lines
    Line distance: 1.0mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model's height
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s setting apply to avoid model deformation. Other settings by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    1,734 downloads

       (0 reviews)

    0 comments

    Updated

  13. Female Shepard 3D printing model from Mass Effect

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    7,942 downloads

       (0 reviews)

    0 comments

    Updated

  14. Lifestealer N'AIX 3D Print Model | Static Figure

    For a smoother and more quality printing, apply the following settings in CURA printing software:
    Quality
    Layer height: 0.1mm
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed: 30mm/s
    Inner shell speed; 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 100mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: Check
    Pattern: Lines
    Line distance: 1.0mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the models height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s setting apply to avoid model deformation. Other settings by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    2,336 downloads

       (0 reviews)

    0 comments

    Updated

  15. Chaos Space Marine 3D Printing Mask

    Quality:
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setup:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation.

    1,449 downloads

       (0 reviews)

    0 comments

    Updated

  16. Atlas 3D Printing Recommendations

    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 30mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 1.5mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.

    1,011 downloads

       (0 reviews)

    0 comments

    Updated

  17. 3D Printed Tesla Power Armor

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    The model has been tested and printed in PLA. In case you need advice where to get your filaments from, check our partner's website.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Lines
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    1,014 downloads

       (0 reviews)

    0 comments

    Updated

  18. Katarina Character from LoL

    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 30mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 1.5mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.

    1,073 downloads

       (0 reviews)

    0 comments

    Updated

  19. Scylla from Smite

    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.

    1,909 downloads

       (0 reviews)

    0 comments

    Updated

  20. Kindred from LoL

    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
     
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.

    808 downloads

       (0 reviews)

    2 comments

    Updated

  21. Female Commander Shepard 3D Model

    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.

    1,025 downloads

       (0 reviews)

    0 comments

    Updated

  22. Legion 3D Model from Mass Effect

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.

    3,499 downloads

       (0 reviews)

    0 comments

    Updated

  23. Lara Croft 3D Model

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed: 30mm/s
    Inner shell speed; 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 100mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Lines
    Line distance: 1.0mm
    Platform adhesion:
    Type: Brim
    Brim Line Count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s setting apply to avoid model deformation. Other settings – by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    2,721 downloads

       (0 reviews)

    0 comments

    Updated

  24. Chaos Space Marine 3D Model-3D Printed and Painted

    This model was tested in Cura 15.06. To avoid printing problems, we recommend the following settings:
    Quality
    Layer height: 0.1mm*
    Initial layer thickness: 0.3mm
    Bottom/top pattern: lines
    Skin perimeter line count: 0
    Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
    *Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
    Speed setups:
    Infill speed: 50mm/s
    Outer shell speed : 30mm/s
    Inner shell speed: 20mm/s
    Top/bottom speed: 20mm/s
    Support speed: 50mm/s
    Travel speed: 150mm/s
    Skirt speed: 30mm/s
    Amount of slower layers: 4
    Infill:
    Infill pattern: Grid
    Line distance: 3mm
    Infill overlap: 20%
    Infill layers: 0
    Support:
    Enable support: Check
    Placement: Everywhere
    Overhang angle: 30°
    X/Y distance: 0.7mm
    Top distance: 0.2mm
    Bottom distance: 0.2mm
    Stair step height: 0.5mm
    Join distance: 0.7mm
    Area smoothing: 0.6mm
    Use towers: check
    Pattern: Grid
    Line distance: 1.5mm
    Platform adhesion:
    Type: Brim
    Brim line count: 10 (up to 20, depending on the model’s height)
    Other 3D printing recommendations:
    Outer Shell Speed - 20mm/s and Support Speed - 40mm/s settings apply to avoid model deformation. Apply other settings by default.
    Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

    2,692 downloads

       (0 reviews)

    0 comments

    Updated

×

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!