Guisao5

Boa tarde pessoal, tenho um Ultimaker 2Go desde 2016, e agora estou pensando em instalar nela uma mesa aquecida, alem do termistor e a mesa o que mais preciso? Sei que as ligacoes na placa já existem mas não deve estar liberados no firmware, alguem tem uma ideia? Grato

I have the same problem, does anyone have any solution. I'm getting to work more or less using the app in low resolution, giving less problems.

I have the same problem, does anyone have any solution. I'm getting to work more or less using the app in low resolution, giving less problems.

Could you tell me if you can remove these lines? ;Generated with Cura_SteamEngine 3.4.1 ;M82 ;absolute extrusion mode ;M190 S105 ;Uncomment to add your own bed temperature line ;M109 S225 ;Uncomment to add your own temperature line G90; EXTRUSORA NO POSICIONAMENTO ABSOLUTO M83; EXTRUSORA NO MODO RELATIVO M106 S255; LIGA VENTILADOR G4 P500; PAUSA MOVIMENTO M106 S0; LIGA VENTILADOR M140 S105; TEMPERATURA DA MESA M190 S105; AGUARDA MESA AQUECER M109 S100; FAZ AQUECIMENTO DO BICO M104 S225; FAZ PRE AQUECIMENTO DO BICO M402 G28; HOME GERAL M400 G29 V4 T ; AUTO NIVELAMENTO M400 G1 X1 Y1 Z0.8 F1000; VAI PRA PONTO DE PURGA M109 S225; FAZ AQUECIMENTO DO BICO G92 E0; RESETA EXTRUSOR G1 X1.0 E9.0 F1000.0 ; PURGA G1 X100.0 E12.5 F1000.0 ; PURGA M117 IMPRIMINDO... M400 G1 E-6.0000 F4200 G1 Z0.600 F3000 T0 ▶︎ E0◀︎ ▶︎ F1500 E-6.5◀︎ ;LAYER_COUNT:654

You did it right, thank you very much.

The gcode does not work as expected in Cura 3.4.1 It's like this in the Start code ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M109 S{print_temperature} ;Uncomment to add your own temperature line G90; EXTRUSORA NO POSICIONAMENTO ABSOLUTO M83; EXTRUSORA NO MODO RELATIVO M106 S255; LIGA VENTILADOR G4 P500; PAUSA MOVIMENTO M106 S0; LIGA VENTILADOR M140 S{print_bed_temperature}; TEMPERATURA DA MESA M190 S{print_bed_temperature}; AGUARDA MESA AQUECER M109 S100; FAZ AQUECIMENTO DO BICO M104 S{print_temperature}; FAZ PRE AQUECIMENTO DO BICO M402 G28; HOME GERAL M400 G29 V4 T ; AUTO NIVELAMENTO M400 G1 X1 Y1 Z0.8 F1000; VAI PRA PONTO DE PURGA M109 S{print_temperature}; FAZ AQUECIMENTO DO BICO G92 E0; RESETA EXTRUSOR G1 X1.0 E9.0 F1000.0 ; PURGA G1 X100.0 E12.5 F1000.0 ; PURGA M117 IMPRIMINDO... M400 G1 E-6.0000 F4200 G1 Z0.600 F3000 T0 Why are you leaving like this? ;FLAVOR:Marlin ;TIME:35423 ;Filament used: 85.3195m ;Layer height: 0.2 ;POSTPROCESSED ;ChangeAtZ instances: 1 ;Generated with Cura_SteamEngine 3.4.1 ▶︎M190 S115 ◀︎ ▶︎M104 S250◀︎ ▶︎M109 S250◀︎ M82 ;absolute extrusion mode ;Sliced at: Thu 12-07-2018 15:09:50 ;Basic settings: Layer height: 0.2 Walls: 1.5 Fill: {fill_density} ;Print time: 09:50:23 ;Filament used: [85.32]m [225.7392328125]g ;Filament cost: [0] ;M190 S110 ;Uncomment to add your own bed temperature line ;M109 S225 ;Uncomment to add your own temperature line G90; EXTRUSORA NO POSICIONAMENTO ABSOLUTO M83; EXTRUSORA NO MODO RELATIVO M106 S255; LIGA VENTILADOR G4 P500; PAUSA MOVIMENTO M106 S0; LIGA VENTILADOR M140 S110; TEMPERATURA DA MESA M190 S110; AGUARDA MESA AQUECER M109 S100; FAZ AQUECIMENTO DO BICO M104 S225; FAZ PRE AQUECIMENTO DO BICO M402 G28; HOME GERAL M400 G29 V4 T ; AUTO NIVELAMENTO M400 G1 X1 Y1 Z0.8 F1000; VAI PRA PONTO DE PURGA M109 S225; FAZ AQUECIMENTO DO BICO G92 E0; RESETA EXTRUSOR G1 X1.0 E9.0 F1000.0 ; PURGA G1 X100.0 E12.5 F1000.0 ; PURGA M117 IMPRIMINDO... M400 G1 E-6.0000 F4200 G1 Z0.600 F3000 T0 G92 E0 G1 F1500 E-6.5

The temperature of the first layer does not change on the machine nor on the gcode despite being specified in the software.

were Z hop when retracting in Cura 2.6???