Jump to content
Ultimaker Community of 3D Printing Experts

curieux

Member
  • Content Count

    26
  • Joined

  • Last visited

Everything posted by curieux

  1. Danke Im Cura hatte ich den UMO schon und beim Firmware upgrade kam keine Auswahl . Ich haue ihn mal weg und mache das Firmware upgrade nochmal . Vllt hatte ich das das Bed doch ausgewählt bei der vorigen Installation.
  2. I have installed a new firmware on the UM0. The firmware assumes that my UMO has a heatable bed. He did not and when printing now the UMO waits until it is heated - So never 😁 Where do I get my old firmware e.g.15.02 again ? About a tool I created a hex file for Marlin , but there is also the heatable bed in it any link or attachement with verg old UMO firmware for me ?
  3. Hi Ich habe auf dem UM0 eine neue Firmware eingespielt . Die Firmware geht davon aus das mein UMO ein beheizbares bed hat Hat er nicht und beim Druck wartet er jetzt bis es aufgeheizt ist - Also niemals 😁 Wo bekomme ich meine alte Firmware 15.02 wieder her ? Über ein Tool habe ich mir ein hex file für Marlin mal zusammengebauen lassen , aber da ist auch das beheizbare bed drin
  4. I dug out a UM original But the previous owner has supplied the wrong springs (yellow) . They are too long and too hard Does anyone have an idea which ones might fit
  5. Hi Ich habe einen UM Original ausgegraben Der Vorbesitzer hat aber die falschen Federn (gelb) mitgeliefert . Die sind zu zu lang und zu hart Hat jemand ein Idee , welche passen könnten
  6. Hi I´ am going abroad and therefore I´´ am looking for UM2+ and um 2go to take along Price < 1000 € for Um2+ and < 500 € for UM 2go regards
  7. did anybody try to print the prusa face mask on an UM2+ ( maybe with S3D slicer ) and can give me the paramater especially the parameters that speed up the whole printing. Filament PLA regards
  8. I am looking for an Ultimaker 2go in Germany. If someone has a UM 2 Go for sale, please send me a message with asking price. email: curieux@web.de
  9. curieux

    Suche UM 2go

    hi Ich suche einen Ultimaker 2go. Wenn jemand einen UM 2 Go zu verkaufen hat, bitte eine Nachricht an mich mit Preisvorstellung. email: curieux@web.de Vielen Dank
  10. Yes that's can be done but that's not really a factory reset. A lot of parameters were changed during the time and the bed and noozle are completely incorrectly calibrated. Back to the beginning
  11. Hi Is there any way to do a factory reset on the um1? Do I have to flash the marlin software do to a reset? A lot of people changes the configuration and now nothing works anymore
  12. Hallo Ich suche einen UM 2 oder besser 2+ mit original Karton und Rechnung zu kaufen
  13. What I understand : cura 4.0 has many options under machine settings -> for the parameter: "g-code flavor" e.g. ultimaker , reprap , marlin RepetierServer has only a few under Firmware : e.g. marlin , reprap Both settings must be equal , so UM2+ starts printing . I tested both values "marlin" and "reprap" cura 4.0 . the result is UM2+ starts printing but the filament gets entangled. the filament wraps around the nozzle. the same file sliced with g-code "ulitmaker" and saved on SD card works fine
  14. Hi Ritxi thanks for your offer but that is too expensive for the old Xtion. My limit is 80 Euro incl. Shipping
  15. yes I´am interested . I ´am liviing in germany . It would be great if you could sent the Xtion to me . What should it cost ?
  16. hi i am looking for the above mentioned scanners. sincerley
  17. Hi Hat jemand mit dem UM2+ und einer Solex 0.25. noozle mal was vernüftiges hinbekommen ? Bei mir löst sich das Objekt mit der Zeit vom Bett ab ( see attach) Wenn mir jemand mal seine Parameter verraten würde wäre das super z.B. Filament ist von "extrudr" Extrusion Multiplexer Extrusion width Primary layer Height First Layer Height 130 Default Printing Speed mm/min
  18. Hi, I can't get any reasonable results with your 0.25 mm noozle with my ultimaker 2+ . I use simplify3d for the slicing process. Does anybody have useful simplifyor Cura parameters for me in conjunction with this noozle diameter ? e.g. Extrusion Multiplexer Extrusion width Primary layer Height First Layer Height 130 Default Printing Speed mm/min The result is always the same wih different parameter ( see attach) the object is detached sincerely curieux
  19. thx I will test it with an enclosure . Its ABS and per default the fans are disabled by Simplify3d
  20. [edit by gr - note that: original post said PLA but it's actually ABS ] Can anybody explain where this cracks coming from ? ( no cover , air draft ) thx in advance
×
×
  • Create New...