[Problems with printed pieces in Ultimaker S5]

Hi all,

I would like to ask you what is the problem if my pieces are printed in this way, with so many deffects in the surface.

I do not know if the problems is about the printer of the parameters of Ultimaker Cura, I am using Ultimaker S5.

Thank you so much.

 

Best regards.

[Is it possible to print two different colors in the same piece with the Ultimaker S5?]

Hi all,

 

I would like to ask you if it is possible to print in two different colors for the same piece using the printer Ultimaker S5 with extruders AA y BB.

Thank you so much.

 

Best regards.

[Problems with printed pieces in Ultimaker S5]

Hi all,

I would like to ask you what is the problem if my pieces are printed in this way, with so many deffects in the surface.

I do not know if the problems is about the printer of the parameters of Ultimaker Cura, I am using Ultimaker S5.

Thank you so much.

 

Best regards.

 

[How to check the lifespan of Air Manager Ultimaker S5?]

Hi all, I would like to know about the lifespan of the air manager of my printer (for example: 190 hours/1500 hours), but I cannot find the option.

Thank you.

 

[Print Cores AA 0,4 does not heat up more that 4 deg.]

Hi all,

 

I have now three broken print cores with this problem: they do not heat up more that 4 deg.

The last one was acquired a week ago and printed only once!

I do not know what is happening, if the problem is print core or the 3d printing Ultimaker S5 get broken all the print cores.

Any solution?

 

Best regards.

[Is it possible to print with PEEK with my Ultimaker S5?]

Hi all,

 

I would like to know if I can print in PEEK material with my Ultimaker S5, taking into account that this material needs printing temperatures as 400 degrees.

Any experience printing with this material? Should I get another print core to support this temperature? Thank you so much.

[Can i print only with print core BB 0,4?]

Dear all,

 

The sensor temperature of print core AA 0,4 of my printer S5 is broken, so I guess if it is possible to use only the print core BB 0,4 mm to print.

Could it be possible? Thank you so much.

 

[Wrong preview Ultimaker Cura]

Thank you so much @dsp, I did not notice that this mode was enable.

[Wrong preview Ultimaker Cura]

Sorry @dsp, but I am not sure to understand you. It happens the same with all the models which I load, indepently of the layer height.

The last layer (the original model is closed by the top) does not appear when preview, so the model is open by the top).

[Wrong preview Ultimaker Cura]

@ahoeben and @dsp, here you can see the original model, the preview and the project.

Thank you for all.

Cura.3mf

[Wrong preview Ultimaker Cura]

Sorry @ahoeben, the problem is that the screen does not show the last layer.

In fact, the model is closed at the top, but in the software the last layer is not showed.

Please confirm me if I have explained rightly, thank you so much.

[Wrong preview Ultimaker Cura]

Dear all,

 

I have the following problem with the software Ultimaker Cura.

When I segment the model, it does not show the last layer, so preview is not seen rightly.

I think it happens since yesterday I moved the left bar to see the layers, but now I do not know how to repair it.

Thank you so much.

 

[Cannot increase temperature print cores]

Hi all,

 

I have a problem with my Ultimaker S5.

The filament is stucked in print core, but this time cannot increase the temperature of it because maximum grades which are alowed are 4ºC.

It is impossible to definy a higer temperature of 28ºC, and I do not know why this happens.

Any solution? Thank you so much!

[Problems when printing with PP (Polypropylene)]

Hi,

 

I am trying to print a piece with PP (Polypropylene) with my printer Ultimaker S5, but the results are terrible.

The warping is considerable and sometimes the pieces cannot keep sticked to the bed for a long time,

even I am using a special glue for that (Magigoo).

These are the parameters which I am using:

 

 

Could you please tell me if I am doing something wrong? In the data sheet of the material, it appears this:

 

 

 

Thank you!

[Filament stuck in print core (Ultimaker S5)]

Thank you so much @MariMakes and @Jasonjason.

Finally, I head the print core up during 10 minutes and with the help of a needle to facilitate the extraction, ir order to use the welder in the filament next to become it longer and be removed with pliers.

[Filament stuck in print core (Ultimaker S5)]

My name is Ana and I have a problem with my printer Ultimaker S5.

The filament is stuck in the print core but I do not know how to remove without dissasembling it.

You can see the picture below.

Thank you for your answer.