Jump to content

Cura calibration do not work


zungara

Recommended Posts

Posted · Cura calibration do not work

I build me Ultimaker und want to first start it

I start Cura and do the firmware update. (I hope it was not a mistake) After the Firmware update the checkup wizard start. But after some seconds i get a message to move the extrude to the middle, but the extruder is in the middle.

here the log:

Object 0x7fd3bb5e0210 of class NSConcreteMapTable autoreleased with no pool in place - just leaking - break on objc_autoreleaseNoPool() to debug

Connecting to: /dev/tty.usbmodemfa1311

Serial(port='/dev/tty.usbmodemfa1311', baudrate=250000, bytesize=8, parity='N', stopbits=1, timeout=2, xonxoff=False, rtscts=False, dsrdtr=False)

0 - abf0693e8e970311cfb66244bb622b092c3fe603 | Author: Build-Me-Marlin

echo: Free Memory: 4420 PlannerBufferBytes: 1232

echo:Using Defa?start

echo: External Reset

Marlin 1.0.0

echo: Last Updated: Marlin-Tue, 4 Sep 2012 08:20:27 +0200 - abf0693e8e970311cfb66244bb622b092c3fe603 | Author: Build-Me-Marlin

echo: Free Memory: 4420 PlannerBufferBytes: 1232

echo:Using Default settings:

echo:Steps per unit:

echo: M92 X78.74 Y78.74 Z533.33 E865.89

echo:Maximum feedrates (mm/s):

echo: M203 X250.00 Y250.00 Z5.00 E45.00

echo:Maximum Acceleration (mm/s2):

echo: M201 X9000 Y9000 Z100 E10000

echo:Acceleration: S=acceleration, T=retract acceleration

echo: M204 S3000.00 T3000.00

echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)

echo: M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00

echo:Home offset (mm):

echo: M206 X0.00 Y0.00 Z0.00

echo:PID settings:

echo: M301 P22.20 I1.08 D114.00

echo:SD init fail

ok

ok

Exception in thread Thread-2:

Traceback (most recent call last):

File "/System/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/threading.py", line 552, in __bootstrap_inner

File "/System/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/threading.py", line 505, in run

File "/Applications/Cura-12.08/Cura/gui/configWizard.py", line 205, in OnRun

wx.MessageBox('Please move the printer head to the center of the machine\nalso move the platform so it is not at the highest or lowest position,\nand make sure the machine is powered on.', 'Machine check', wx.OK | wx.ICON_INFORMATION)

File "/usr/local/lib/wxPython-2.9.3.1/lib/python2.7/site-packages/wx-2.9.3-osx_cocoa/wx/_misc.py", line 491, in MessageBox

return _misc_.MessageBox(*args, **kwargs)

PyAssertionError: C++ assertion "Assert failure" failed at /BUILD/wxPython-src-2.9.3.1/src/common/utilscmn.cpp(1379) in wxMessageBox(): unexpected return code from wxMessageDialog

  • Link to post
    Share on other sites

    Posted · Cura calibration do not work

    The firmware update is good (the supplied firmware is quite new but very stable)

    On Mac the wizard fails for some reason, not sure why yet. I've had more reports. Just skip the wizard for now.

  • Link to post
    Share on other sites

    Posted · Cura calibration do not work

    Ok, Thank you.

    I have switched to Windows and i installed Cura to see weather the check runs there.

    But i still have a Problem. I failed again. After temperature check i should press X End in front left corner. I moved the extruder bye hand to left but nothing happens.

  • Link to post
    Share on other sites

    Posted · Cura calibration do not work

    x and y calibration works now. But the z calibration will not work. I can touch the end stopper per Hand but there is no reaction. I have have checked the cabeling but i found no mistake..

  • Link to post
    Share on other sites

    Posted · Cura calibration do not work

    Check the switch with a multi-meter, also I took about 5 attempts to get CURA to "see" the switches going. For me it certainly was not a case of quickly clicking each switch and being done in 15 seconds, sometimes when it asked for the X LH endstop I would have to sit there clicking it for half a minuite before CURA reacted.

  • Link to post
    Share on other sites

    Posted · Cura calibration do not work

    ok i will try it. I think it have to be a SW problem, because moving the z-plattform stops after reaching the end stop. (Automoving to 0,0,0 works fine)

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.8 Stable released 🎉
        In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
        • 5 replies
      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
    ×
    ×
    • Create New...