Jump to content
UltiMaker Community of 3D Printing Experts

Ultimaker Original Heated Bed upgrade manual question


LePaul

Recommended Posts

Posted · Ultimaker Original Heated Bed upgrade manual question

A couple comments/constructive criticism about the guide I downloaded, version 1.3

(I'm reading it prior to purchasing the upgrade)

1) I don't know if this is a Europe vs American layout style sort of thing but the directions jump around.

I would expect the directions and pictures to go Left to Right. Not.. Up, Down, Far right up, Far right down, as they seem to be. I find it awkward to follow along. (As an example, I am trying to read along as I would a comic book)

2) There is no mention on how to attach the Z-screw to the new stepper motor. Perhaps easy to sort out once the pieces are in front of you. But going through the steps, it was just magically assembled already :)

3) The first steps of the directions state to remove the top caps (3B) and then shows a photo of the caps, 3A and 3B. The directions should include removing the lower caps (3A) :)

Again, not being picky, just trying to be helpful!

  • Link to post
    Share on other sites

    Posted · Ultimaker Original Heated Bed upgrade manual question

    1. At least in the part of Europe I live we also read first from left to right and then from top to bottom...

    2. Assemble!?! Z screw and motor is one unit....

    3. I actually see not much need to remove the lower caps anyway unless the rods are completely stuck...

  • Link to post
    Share on other sites

    Posted · Ultimaker Original Heated Bed upgrade manual question

    Its all together already? Very good!

    I was a little surprised at the removing of the lower caps too

    If you read the guide, its interesting the layout used.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • UltiMaker Cura 5.3 stable released
        In this stable release, Cura 5.3 achieves yet another huge leap forward in 3D printing thanks to material interlocking! As well as introducing an expanded recommended print settings menu and lots of print quality improvements. Not to mention, a whole bunch of new printer profiles for non-UltiMaker printers!
          • Thanks
        • 21 replies
      • Here it is. The new UltiMaker S7
        The UltiMaker S7 is built on the success of the UltiMaker S5 and its design decisions were heavily based on feedback from customers.
         
         
        So what’s new?
        The obvious change is the S7’s height. It now includes an integrated Air Manager. This filters the exhaust air of every print and also improves build temperature stability. To further enclose the build chamber the S7 only has one magnetically latched door.
         
        The build stack has also been completely redesigned. A PEI-coated flexible steel build plate makes a big difference to productivity. Not only do you not need tools to pop a printed part off. But we also don’t recommend using or adhesion structures for UltiMaker materials (except PC, because...it’s PC). Along with that, 4 pins and 25 magnets make it easy to replace the flex plate perfectly – even with one hand.
         
        The re-engineered print head has an inductive sensor which reduces noise when probing the build plate. This effectively makes it much harder to not achieve a perfect first layer, improving overall print success. We also reversed the front fan direction (fewer plastic hairs, less maintenance), made the print core door magnets stronger, and add a sensor that helps avoid flooding.
         

         
        The UltiMaker S7 also includes quality of life improvements:
        Reliable bed tilt compensation (no more thumbscrews) 2.4 and 5 GHz Wi-Fi A 1080p camera (mounted higher for a better view) Compatibility with 280+ Marketplace materials Compatibility with S5 project files (no reslicing needed) And a whole lot more  
        Curious to see the S7 in action?
        We’re hosting a free tech demo on February 7.
        It will be live and you can ask any questions to our CTO, Miguel Calvo.
        Register here for the Webinar
          • Like
        • 18 replies
      • UltiMaker Cura Alpha 🎄 Tree Support Spotlight 🎄
        Are you a fan of tree support, but dislike the removal process and the amount of filament it uses? Then we would like to invite you to try this special release of UltiMaker Cura. Brought to you by our special community contributor @thomasrahm
         
        We generated a special version of Cura 5.2 called 5.3.0 Alpha + Xmas. The only changes we introduced compared to UltiMaker Cura 5.2.1 are those which are needed for the new supports. So keep in mind, this is not a sneak peek for Cura 5.3 (there are some really cool new features coming up) but a spotlight release highlighting this new version of tree supports.  
          • Like
        • 21 replies
    ×
    ×
    • Create New...