Jump to content

Prints coming out slanted!

worthy7777

By worthy7777
in UltiMaker 3D printers

 Share

Recommended Posts

worthy7777

worthy7777 3

Posted
Posted · Prints coming out slanted!

I am using an ultimaker original (Do not have a heated bed) and I am printing in PLA at 210 c, Every print I have done so far and come out slanted facing forward. I have levelled the bed twice now and I am still getting the same results, i have checked that the Y axis is moving the correct distance and still nothing. Here is a picture of two of my prints that have turned out slanted.

IMG_0345.thumb.JPG.e7011a42d1463c85f97651622074cf23.JPG

IMG_0344.thumb.JPG.3dc1a048338a8f265d9c78f9365b6e27.JPG

IMG_0345.thumb.JPG.e7011a42d1463c85f97651622074cf23.JPG

IMG_0344.thumb.JPG.3dc1a048338a8f265d9c78f9365b6e27.JPG

    • Link to post
    Share on other sites
    LePaul

    LePaul 322

    Posted
    Posted · Prints coming out slanted!

    The basics...make sure the pulleys are firmly in place, make sure those set screws are in tight. Something seems slightly out of alignment to generate prints like that.

    Has this just started to happen? Or had the printer worked fine for a while and now this is occurring?

    • Link to post
    Share on other sites
    worthy7777

    worthy7777 3

    Posted
    • Author
    Posted · Prints coming out slanted!

    No worries i have tightened all the pulleys and made sure that the belt was not rubbing on the frame and now all is working again. Thanks for the help!

    • Like 1
    Link to post
    Share on other sites
    rigs

    rigs 735

    Posted
    Posted · Prints coming out slanted!

    happy printing :)

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 1
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 26 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...