UltiMaker uses functional, analytical and tracking cookies. Tracking cookies enhance your experience on our website and may also collect your personal data outside of Ultimaker websites. If you agree with the use of tracking cookies, click “I agree, continue browsing”. You can withdraw your consent at any time. If you do not consent with the use of tracking cookies, click “Refuse”. You can find more information about cookies on our Privacy and Cookie Policy page.
Next time try to stop it from printing much sooner. At this point your filament is probably ground to dust in the feeder so you will have to fix that issue first.
Not sure why it stopped. It looks like you have 2 different colors though? White then gray?
I'm thinking the gray filament never loaded properly. I always cut the tip of the filament to a point before loading - you probably have the filament stuck just at the lip of the white part (the teflon part) inside the head. After fixing the other issue try "move material" and move filament up and down until it gets past that ledge and it starts extruding. Extrude for a while to get any burnt PLA out of the nozzle.
Now to your other issue - likely ground filament. First turn off power and pull firmly out the bottom. If the entire filament comes out then yay - just cut it off and throw it away and reload (but now with sharpened tip).
If the filament breaks at the feeder then remove bowden from feeder: remove the horse shoe shaped clip, push down hard on the outer white clip and then lift firmly on the bowden (the clear tube) (again this is at the feeder, not the head). Do not lift on the bowden untill you can get the clip to go down otherwise the metal blades in the bowden holder will scratch up your bowden (not a disaster but you can only do this so many times - if you scrape badly you can always cut the last 2mm off the end of the bowden).
Now you should be able to pull the filament up through the feeder and then out through the tube - throw it away and put it back together and start over.
Thank you for the guidance. It worked after pulling out the filament and loading it back again. Yes, I had to dismantle the 'head' and put it all back again.
Link to post
Share on other sites
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
In the Cura 5.8 stable release, everyone can now tune their Z seams to look better than ever. Method series users get access to new material profiles, and the base Method model now has a printer profile, meaning the whole Method series is now supported in Cura!
We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
Recommended Posts
gr5 2,224
Next time try to stop it from printing much sooner. At this point your filament is probably ground to dust in the feeder so you will have to fix that issue first.
Not sure why it stopped. It looks like you have 2 different colors though? White then gray?
I'm thinking the gray filament never loaded properly. I always cut the tip of the filament to a point before loading - you probably have the filament stuck just at the lip of the white part (the teflon part) inside the head. After fixing the other issue try "move material" and move filament up and down until it gets past that ledge and it starts extruding. Extrude for a while to get any burnt PLA out of the nozzle.
Now to your other issue - likely ground filament. First turn off power and pull firmly out the bottom. If the entire filament comes out then yay - just cut it off and throw it away and reload (but now with sharpened tip).
If the filament breaks at the feeder then remove bowden from feeder: remove the horse shoe shaped clip, push down hard on the outer white clip and then lift firmly on the bowden (the clear tube) (again this is at the feeder, not the head). Do not lift on the bowden untill you can get the clip to go down otherwise the metal blades in the bowden holder will scratch up your bowden (not a disaster but you can only do this so many times - if you scrape badly you can always cut the last 2mm off the end of the bowden).
Now you should be able to pull the filament up through the feeder and then out through the tube - throw it away and put it back together and start over.
Link to post
Share on other sites