Jump to content

extruding problems with ultimaker v2 using olsson block


ferdinand981

Recommended Posts

Posted · extruding problems with ultimaker v2 using olsson block

I seem to have an extruding problems with ultimaker v2 using olsson block by using th 0.4 and 0.8 nozzle

I can hear the stepper motor skipping steps and see an under extrudin in my prints what should I do

210C nozzle

60C bad

50mm/s speed

I have seen this problem occur in 100 to 200 microns z resolution

  • Link to post
    Share on other sites

    Posted · extruding problems with ultimaker v2 using olsson block

    OK, here are a few questions for narrowing down the issue:

    - Is it a new problem of a configuration which previously worked? Did you successfully print with the Olsson block?

    - How stable is the temperature?

    - Have you performed some cold pulls?

    - Have you tried to print hotter? 210°C is certainly too cold for printing at 50mm/s with a 0.8mm nozzle and 0.2mm layer height.

    - Is the Bowden tube undamaged and clean?

    - Are the teflon and the stainless steel isolator sitting at their correct places? Any gaps?

    - Did you change the nozzle while it was hot?

  • Link to post
    Share on other sites

    Posted · extruding problems with ultimaker v2 using olsson block

    I'm currently using the 0.4 nozzle and getting extruding problems add 210c 50mms

    The printer is four days old should be undamaged as well as clean and teflon should still be as good as new I currently have a 2 mm gap in between the stainless steel isolator and the teflon like recommended in the Ultimaker ios app.

    I always change the nozzle at around 150c since it is a lot easier at that temperature

    I have did some cold pulls like you recommended but it make no difference :(

  • Link to post
    Share on other sites

    Posted · extruding problems with ultimaker v2 using olsson block

    It's the stock filament what comes with the Ultimaker. it happens in the first layer as well as the layers after. But it doesn't happen in every print even if it is the same model sometimes it does sometimes it doesn't under extrude so it's not really consistent

  • Link to post
    Share on other sites

    Posted · extruding problems with ultimaker v2 using olsson block

    How does your first layer look like?

    If it's really squished then maybe the bed is a bit to close and the filament has a hard time to come out. This could damage the filament in the feeder and cause more underextrusion after

  • Link to post
    Share on other sites

    Posted · extruding problems with ultimaker v2 using olsson block

    Yes it does look like the first layer is quite squished

    Should I do another bed calibration

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 26 replies
    ×
    ×
    • Create New...