Jump to content

Cura 2.3.1 failed to update firmware on UMO+

Gencab

By Gencab
in UltiMaker Cura

 Share

Recommended Posts

Gencab

Gencab 19

Posted
Posted · Cura 2.3.1 failed to update firmware on UMO+

Well as the title. I have a UMO+ and Cura 2.3.1 fails to update the firmware every time.

White Board rev 2.1.4

Last firmware update from Cura 15.04.6

Tried 2 different computers and multiple USB cables. It seems to update/reload fine with the 15 series Cura. No custom firmware ever loaded.

    • Link to post
    Share on other sites
    neotko

    neotko 1,417

    Posted
    Posted (edited) · Cura 2.3.1 failed to update firmware on UMO+

    Just a friendly note. Don't update. UMO+ doesn't have any interesting update from UM since almost two years ago.

    Edited by Guest
    • Like 1
    Link to post
    Share on other sites
    ahoeben

    ahoeben 1,948

    Posted
    Posted · Cura 2.3.1 failed to update firmware on UMO+

    I agree with neotoko. Having said that, it should work. How does Cura fail? Does it try for a while and give up? Does it give any error message? Does the printer restart at all?

    • Like 1
    Link to post
    Share on other sites
    Gencab

    Gencab 19

    Posted
    • Author
    Posted · Cura 2.3.1 failed to update firmware on UMO+

    I agree with neotoko. Having said that, it should work. How does Cura fail? Does it try for a while and give up? Does it give any error message? Does the printer restart at all?

     

    It starts the loading process then within 5 seconds fails. After that the printer restarts about 20 seconds later.

    neotko your advice is well founded. Ill leave it be unless there is some noteworthy improvement. Thanks for the advice.

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...