Jump to content

Bondtech QR 3.0 Ultimaker 2+ kein gehärteter Stahl?

jeracom

By jeracom
in Deutsch

 Share

Recommended Posts

jeracom

jeracom 4

Posted
Posted (edited) · Bondtech QR 3.0 Ultimaker 2+ kein gehärteter Stahl?

Hmm, hat immer gedacht, da die Ersatzteile auch gehärteter Stahl sind, da passiert sowas nicht. Heute beim reinigen, Madenscharaube festgezogen, nicht mal übermäßig, und Zack, gerissen.

Ist das jemanden von euch auch schon passiert?

Wo bei ich gestehen muss es sieht hier eher aus wie Alu, ist aber magnetisch...

 

 

bondtech.jpg

Edited by jeracom
    • Link to post
    Share on other sites
    zerspaner_gerd

    zerspaner_gerd 382

    Posted
    Posted · Bondtech QR 3.0 Ultimaker 2+ kein gehärteter Stahl?

    Mhh

    Nach fest kommt ab 🙄 😂

     

    Vielleicht auch falsch (durch) gehärtet, falsch gehärteter Stahl kann einfach von auf der kante schlagen brechen.

    Meist wird ja nur die Oberfläche gehärtet

     

    Oder ein Material Fehler

    • Link to post
    Share on other sites
    jeracom

    jeracom 4

    Posted
    • Author
    Posted (edited) · Bondtech QR 3.0 Ultimaker 2+ kein gehärteter Stahl?

    Jo, nach fest kommt ab 🙂

    Ne, war aber wirklich nicht stark und das mit einer stinknormalen Madenschraube. Egal, hab Ersatz bestellt

     

    Edited by jeracom
    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 1
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...