Jump to content

Temp Tower gedruckt mit Cura 4.13.1

Krokus

By Krokus
in Deutsch

 Share

Recommended Posts

Krokus

Krokus 0

Posted
Posted · Temp Tower gedruckt mit Cura 4.13.1

Hallo, Ich arbeite mit Cura 4.13.1.  Wenn ich ein Temp Tower herstelle, z.B. "Heat_tower_190-240_Bridge.stl" (siehe Bild 1), ein Post-Skript mache und dann Slice entsteht beim Drucken der Körper in Bild 2. 

Der Abstand zwischen den Streifen ist ausgefüllt. Sollte doch wie im Bild 1 aussehen. Was mache ich falsch? Für eine Antwort bin ich sehr dankbar. Vielen Dank

Bild 2_Temp Tower gedruckt mit CURA.JPG

Bild 1_Temp Tower als stl.JPG

    • Link to post
    Share on other sites
    Krokus

    Krokus 0

    Posted
    • Author
    Posted · Temp Tower gedruckt mit Cura 4.13.1

    Hallo Falko

    Vielen Dank für deine Hilfe. Es gibt mehrere Kästchen mit Stützstrukturen. Welche muss ich entfernen?
    Vielen Dank,  Krokus

    Stützstruktur.JPG

    • Link to post
    Share on other sites
    ManAtArms

    ManAtArms 59

    Posted
    Posted · Temp Tower gedruckt mit Cura 4.13.1

    Das sind nur die Felder die angezeigt werden sollen in der rechten Leiste bei der Druckeransicht.

    Du musst das in der Leiste einstellen und nicht bei den Einstellungen in Cura.

     

     

    Support.jpg

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 2
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...