Jump to content

Drucker druckt nach ca 10 mm Höhe immer schlechter.


Klinki04

Recommended Posts

Posted · Drucker druckt nach ca 10 mm Höhe immer schlechter.

 

 

Ich habe neuerdings das Problem wenn ich PLA drucke das der Drucker (Ultimaker S5) ab einer gewissen Layerhöhe nicht mehr richtig druckt.

Es sieht so aus, als wenn es eine Art Unterextrusion ist. Ich habe bereits die Extruder gewechselt sowie gereinigt, die Schläuche sind auch sauber.

Ich habe Cura 5.4 neu installiert und den Drucker auf Werkseinstellung gesetzt. Habe verschiedene Modelle und PLA Typen probiert mit dem

Gleichen Ergebnis. 

Habe auch die Füllgeschwindigkeit verändert und mit mehr und weniger Infield gedruckt.

Komisch ist das, es ja mal funktioniert hat, ohne Probleme

 

 

 

Fehldruck.jpg

  • Link to post
    Share on other sites

    Posted · Drucker druckt nach ca 10 mm Höhe immer schlechter.

    Hallo @Klinki04,

    was mir bei Deinem Symtom als erstes einfällt, ist ein mögliches Problem mit dem Frontlüfter. Überprüfe, ob der sich frei drehen kann, oder ggf. durch Filamentfäden verschmutzt ist (siehe Wartungsplan). Des weiteren muß der Lüfter immer laufen, wenn und sobald mindestens ein Druckkern die 60°C-Schwelle überschritten hat.

    Wenn der Lüfter ab 60°C nicht läuft, führt dies zu einer Hitzeausdehnung bis in den kalten Bereich des Druckkopfs und verursacht dort Verstopfungen, was zu dem von Dir beschriebenen Problem führen kann.

    Grüße

     

    Ach ja, und nochwas: Im "allgemeinen" Forum schreiben wir gewöhnlich in Englisch, für deutsche Beiträge ist das deutsche Forum (weiter unten auf der Hauptseite) der richtige Platz. Daher meine Antwort jetzt nochmal auf Englisch:

     

    Hi,

    the first thing that comes to mind with your symptom is a possible problem with the front fan. Check if the fan can rotate freely or if it is contaminated by filament threads (see maintenance plan). Furthermore, the fan must always run when and as soon as at least one print core has exceeded the 60°C threshold.

    If the fan does not run above 60°C, this will cause heat to expand into the cold area of the printhead and cause clogging there, which can lead to the problem you describe.

    Regards


    Oh, and one more thing: In the "general" forum we usually write in English, for German posts the German forum (further down on the main page) is the right place. Therefore my answer now again in English:

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing the UltiMaker Factor 4
        We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
          • Thanks
          • Like
        • 3 replies
      • UltiMaker Cura 5.7 stable released
        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 26 replies
    ×
    ×
    • Create New...